EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fiber-Based Hydrogels for Designing Viscoelastic Responses in Particle-Based Biomaterials That Support Embedded 3D Printing

M Gregory Grewal, Emily Ferrarese, Lauren Porter, Georgia T Helein, Christopher B Highley iD

ACS Biomaterials Science & Engineering · 08.06.2026 · 12 (6) · 3165-3176

DOI: 10.1021/acsbiomaterials.5c01432 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Biomaterials Science & Engineering, online erschienen am 01.05.2026. Verfasst von M Gregory Grewal und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemical Engineering, University of Virginia, 385 McCormick Rd., Charlottesville, Virginia 22903, United States. Hauptthemen laut MEDLINE: Hydrogels, Printing, Three-Dimensional, Biocompatible Materials. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 69 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: NIGMS NIH HHS, National Institute of General Medical Sciences.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Viscoelastic biomaterials that exhibit biomimetic responses to applied stresses are important in studying physiology and designing biomaterial scaffolds. Particle-based hydrogels offer potential for engineering viscoelasticity through the design of both the component microparticles and their processing into bulk particle-based materials. When particles are not cross-linked to one another, particle movements in response to strain can potentially relieve applied stresses and facilitate the material's use in dynamic processes like bioprinting. In particle-based hydrogels based on spherical hydrogel microparticles (HMPs), particle movement is restricted by contact with immediately adjacent HMPs. In comparison, fiber-based hydrogel systems leverage high-aspect-ratio microfiber components with long-range interactions. Here, microfibers with aspect ratios of ∼15:1 length/diameter are used to form particle-based hydrogels to compare how interparticle interactions at increased length scales alter properties compared to particle-based hydrogels based on spherical HMPs. Like particle-based hydrogels formed from spherical HMPs, those formed from fiber HMPs exhibit viscoelasticity with shear-thinning and self-healing behaviors. But fiber-based materials allow enhanced control over bulk stress relaxation times (T1/2 ∼ 1-100+ s) across a range of applied strains (σ ∼ 2.5%-50%) in a packing density-dependent fashion. Fiber-based systems relaxed stresses continuously and to a greater degree at low strains in comparison to HMP systems. Dynamic interfiber interactions in fiber-based hydrogels also supported embedded printing, where perfusable channels can be printed into fiber-based hydrogels stabilized by physical interfiber interactions. Taken together, fiber-based hydrogels offer opportunities for designing complex biomaterial scaffolds, including allowing control over viscoelastic properties through hydrogel design and control over heterogeneous 3D structures through embedded printing.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

HydrogelsPrinting, Three-DimensionalBiocompatible MaterialsViscosityElasticityParticle Size

Stichwörter der Autor:innen

dynamic materialsembedded printinggranular hydrogelsmicrofibersparticle-based hydrogelsstress relaxation

Substanzen

HydrogelsBiocompatible Materials

Autor:innen und Institutionen

  • Department of Chemical Engineering, University of Virginia, 385 McCormick Rd., Charlottesville, Virginia 22903, United States.
  • Department of Biomedical Engineering, University of Virginia, 415 Lane Rd., Charlottesville, Virginia 22908, United States.

ORCID-Profile: Christopher B Highley

Förderung

  • NIGMS NIH HHS
  • National Institute of General Medical Sciences

Zitieren

APA

Grewal, M. G., Ferrarese, E., Porter, L., Helein, G. T., & Highley, C. B. (2026). Fiber-Based Hydrogels for Designing Viscoelastic Responses in Particle-Based Biomaterials That Support Embedded 3D Printing. ACS Biomaterials Science & Engineering, 12(6), 3165-3176. https://doi.org/10.1021/acsbiomaterials.5c01432

Vancouver

Grewal MG, Ferrarese E, Porter L, Helein GT, Highley CB. Fiber-Based Hydrogels for Designing Viscoelastic Responses in Particle-Based Biomaterials That Support Embedded 3D Printing. ACS Biomaterials Science & Engineering. 2026;12(6):3165-3176. doi:10.1021/acsbiomaterials.5c01432

BibTeX
@article{Grewal2026,
  author = {Grewal, M Gregory and Ferrarese, Emily and Porter, Lauren and Helein, Georgia T and Highley, Christopher B},
  title = {Fiber-Based Hydrogels for Designing Viscoelastic Responses in Particle-Based Biomaterials That Support Embedded 3D Printing},
  journal = {ACS Biomaterials Science & Engineering},
  year = {2026},
  volume = {12},
  number = {6},
  pages = {3165--3176},
  doi = {10.1021/acsbiomaterials.5c01432}
}
Kostenlos starten →