EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fabrication and Characterization of a Porous TiO2‑Modified PEEK Scaffold with Enhanced Flexural Compliance for Bone Tissue Engineering

Martina Galea Mifsud iD, Andrew Sachan, Roger J Narayan, Lucy Di-Silvio, Trevor Coward

ACS Biomaterials Science & Engineering · 13.10.2025 · 11 (10) · 5838-5849

DOI: 10.1021/acsbiomaterials.5c01032 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Biomaterials Science & Engineering, online erschienen am 23.09.2025. Verfasst von Martina Galea Mifsud und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Dentistry, Oral & Craniofacial Sciences, King's College London, London SE1 9RT, U.K. Hauptthemen laut MEDLINE: Titanium, Ketones, Polyethylene Glycols, Tissue Scaffolds. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 63 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science Foundation, Department of Energy, Office of Science, Office of Basic Energy Sciences.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Bone pathologies are becoming increasingly prevalent with an aging population, often necessitating bone grafting procedures. The current gold standard for grafting uses autologous tissue; however, this approach carries limitations such as donor site morbidity. Consequently, there is a growing interest in alternative biomaterials. Polyetheretherketone (PEEK), a thermoplastic with bone-like mechanical properties, has shown promise, although its limited bioactivity remains a critical constraint. Various functionalization strategies have been employed to enhance the biological performance of otherwise inert materials. This study aims to develop a functionalized porous PEEK scaffold to improve bioactivity of the material, thereby promoting human osteoblast (HOB) adhesion, proliferation, and differentiation. PEEK scaffolds were fabricated using fused deposition modeling (FDM) (Apium P155), with a rectilinear pattern alternating at +45° and −45° angles between layers. This configuration generated an interconnected pore network with sizes ranging from ∼100 to 400 μm. The scaffolds were further coated with titanium oxide as an additional intervention to enhance bioactivity. Mechanical properties of both porous and solid constructs were evaluated according to ISO 178, a flexural testing standard for plastics. Results indicated that both porous scaffolds exhibited a 10-fold decrease in flexural modulus and were 10 times more flexible compared to the solid counterpart (p < 0.001). The mechanical properties of both porous scaffolds were consistent with values reported for trabecular bone, while the solid construct demonstrated a flexural modulus comparable to cortical bone. These findings suggest that the porous PEEK scaffold, both neat and titanium oxide-coated, possesses mechanical properties similar to bone in vivo, indicating its potential as a mechanically suitable biomaterial for bone grafting applications.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

TitaniumKetonesPolyethylene GlycolsTissue ScaffoldsTissue EngineeringBone and BonesBenzophenonesPorosityHumansOsteoblastsPolymersCell ProliferationCell AdhesionBiocompatible MaterialsCell DifferentiationMaterials Testing

Stichwörter der Autor:innen

3D printingbiomaterial characterizationbone tissue engineeringmechanical propertiespolyetheretherketone scaffoldtitanium dioxide coating

Substanzen

TitaniumBenzophenonespolyetheretherketoneKetonesPolyethylene GlycolsPolymerstitanium dioxideBiocompatible Materials

Autor:innen und Institutionen

  • Faculty of Dentistry, Oral & Craniofacial Sciences, King's College London, London SE1 9RT, U.K.
  • Joint Department of Biomedical Engineering, University of North Carolina and Carolina State University, Raleigh, North Carolina 27695-7115, United States.

ORCID-Profile: Martina Galea Mifsud

Förderung

  • National Science Foundation
  • Department of Energy, Office of Science, Office of Basic Energy Sciences

Zitieren

APA

Galea Mifsud, M., Sachan, A., Narayan, R. J., Di-Silvio, L., & Coward, T. (2025). Fabrication and Characterization of a Porous TiO2‑Modified PEEK Scaffold with Enhanced Flexural Compliance for Bone Tissue Engineering. ACS Biomaterials Science & Engineering, 11(10), 5838-5849. https://doi.org/10.1021/acsbiomaterials.5c01032

Vancouver

Galea Mifsud M, Sachan A, Narayan RJ, Di-Silvio L, Coward T. Fabrication and Characterization of a Porous TiO2‑Modified PEEK Scaffold with Enhanced Flexural Compliance for Bone Tissue Engineering. ACS Biomaterials Science & Engineering. 2025;11(10):5838-5849. doi:10.1021/acsbiomaterials.5c01032

BibTeX
@article{GaleaMifsud2025,
  author = {Galea Mifsud, Martina and Sachan, Andrew and Narayan, Roger J and Di-Silvio, Lucy and Coward, Trevor},
  title = {Fabrication and Characterization of a Porous TiO2‑Modified PEEK Scaffold with Enhanced Flexural Compliance for Bone Tissue Engineering},
  journal = {ACS Biomaterials Science & Engineering},
  year = {2025},
  volume = {11},
  number = {10},
  pages = {5838--5849},
  doi = {10.1021/acsbiomaterials.5c01032}
}
Kostenlos starten →