EUVIMEDEUVIMED entdecken
Crossref

Design of Printable Gelatin Composite-PVA Bioink for Self-Supported Fabrication of 3D Thick Porous Constructs

Renjing Wang, Yunxia Chen iD, Kyle R Phillips iD, Chuanshen Zhou, John-Thomas T Robinson iD, David B Iten, Dylan Z Ver Helst, Yong Huang iD

ACS Biomaterials Science & Engineering · 13.10.2025 · 11 (10) · 6234-6247

DOI: 10.1021/acsbiomaterials.5c00888 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Biomaterials Science & Engineering, online erschienen am 03.09.2025. Verfasst von Renjing Wang und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, Florida 32611-6250, United States. Hauptthemen laut MEDLINE: Gelatin, Polyvinyl Alcohol, Printing, Three-Dimensional, Tissue Scaffolds. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 41 Literaturangaben. Gefördert von: National Science Foundation, National Heart, Lung, and Blood Institute, National Cancer Institute.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The development of thick, permeable, three-dimensional (3D) constructs is essential for advancing tissue engineering applications that require efficient mass transport and prolonged cell viability. In this study, a printable gelatin composite-poly­(vinyl alcohol) (PVA) bioink is designed and evaluated for the self-supported fabrication of 3D thick porous constructs with satisfactory permeability. The proposed bioink incorporates gelatin solution, gelatin microgels, and PVA, which is utilized as a sacrificial porogen to facilitate postprinting pore formation. The rheological properties of the bioink (the PVA-to-gelatin composite v/w ratio of 1:5) demonstrate suitable shear-thinning behavior and yield-stress fluid property for extrusion-based 3D printing, and the latter enables the jamming-based physical cross-linking mechanism during printing, which works with the thermal cross-linking of gelatin solution to retain the print shape for permanent enzymatic cross-linking. Printed constructs exhibit good print fidelity and structural integrity across both two-dimensional (2D) lattice and 3D tubular geometries. After PVA removal, the freeze-dried samples show large pores formed by removed PVA, as confirmed by scanning electron microscopy and pore size analysis. Permeability tests reveal that constructs fabricated with PVA porogen removal achieve a higher permeation rate of 1.39 mm/h. NIH 3T3 fibroblast-based cell viability studies demonstrate sustained cell survival in the 10.00 mm-thick porous constructs with cell viability above 75% over 7 days with the 2D cell viability control effect considered. Despite residual PVA detected postremoval, the porous network formed by PVA removal remains effective in supporting permeability and cellular function. These findings demonstrate the potential of the printable gelatin composite-PVA bioink for fabricating thick, permeable constructs suitable for cell culture and tissue engineering applications.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

GelatinPolyvinyl AlcoholPrinting, Three-DimensionalTissue ScaffoldsPorosityAnimalsMiceTissue EngineeringNIH 3T3 CellsInkBioprintingCell SurvivalPermeability

Stichwörter der Autor:innen

bioinkgelatin compositepermeabilityprintableself-supported printingthick porous construct

Substanzen

GelatinPolyvinyl Alcohol

Autor:innen und Institutionen

  • Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, Florida 32611-6250, United States.
  • J. Crayton Pruitt Family Department of Biomedical Engineering, University of Florida, Gainesville, Florida 32611-6250, United States.
  • Department of Materials Science and Engineering, University of Florida, Gainesville, Florida 32611-6250, United States.

ORCID-Profile: Yunxia Chen, Kyle R Phillips, John-Thomas T Robinson, Yong Huang

Förderung

  • National Science Foundation
  • National Heart, Lung, and Blood Institute
  • National Cancer Institute

Zitieren

APA

Wang, R., Chen, Y., Phillips, K. R., Zhou, C., Robinson, J. T., Iten, D. B., Ver Helst, D. Z., & Huang, Y. (2025). Design of Printable Gelatin Composite-PVA Bioink for Self-Supported Fabrication of 3D Thick Porous Constructs. ACS Biomaterials Science & Engineering, 11(10), 6234-6247. https://doi.org/10.1021/acsbiomaterials.5c00888

Vancouver

Wang R, Chen Y, Phillips KR, Zhou C, Robinson JT, Iten DB, et al. Design of Printable Gelatin Composite-PVA Bioink for Self-Supported Fabrication of 3D Thick Porous Constructs. ACS Biomaterials Science & Engineering. 2025;11(10):6234-6247. doi:10.1021/acsbiomaterials.5c00888

BibTeX
@article{Wang2025,
  author = {Wang, Renjing and Chen, Yunxia and Phillips, Kyle R and Zhou, Chuanshen and Robinson, John-Thomas T and Iten, David B and Ver Helst, Dylan Z and Huang, Yong},
  title = {Design of Printable Gelatin Composite-PVA Bioink for Self-Supported Fabrication of 3D Thick Porous Constructs},
  journal = {ACS Biomaterials Science & Engineering},
  year = {2025},
  volume = {11},
  number = {10},
  pages = {6234--6247},
  doi = {10.1021/acsbiomaterials.5c00888}
}
Kostenlos starten →