EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Highly Elastic, Biodegradable Polyester-Based Citrate Rubber for 3D Printing in Regenerative Engineering

Amir Khan iD, Yonghui Ding, Rao Fu, Xinlong Wang, Maria Mendez-Santos, Shivakalyani Adepu, Cheng Sun iD, Guillermo A Ameer iD

ACS Biomaterials Science & Engineering · 2025

DOI: 10.1021/acsbiomaterials.4c01486 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Biomaterials Science & Engineering, 2025. Verfasst von Amir Khan und 7 weiteren Autor:innen. Beteiligte Einrichtung: Center for Advanced Regenerative Engineering (CARE), Northwestern University, Evanston, Illinois 60208, United States. Hauptthemen laut MEDLINE: Polyesters, Printing, Three-Dimensional, Rubber, Tissue Engineering. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: NIBIB NIH HHS, National Institutes of Health, Northwestern University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Highly elastic and 3D-printable degradable elastomers are advantageous for many biomedical applications. Herein, we report the synthesis of a biodegradable citrate rubber poly(tetrahydrofuran-co-citrate-co-hydroxyl telechelic natural rubber) (PTCR) using citric acid, poly(tetrahydrofuran), and hydroxyl telechelic natural rubber. The citrate rubber PTCR is methacrylated to synthesize a prepolymer methacrylated-PTCR (mPTCR) that can be used to fabricate bioresorbable scaffolds via 3D printing using micro-continuous liquid interface production. Polymers were chemically characterized via NMR spectroscopy, FTIR spectroscopy, DSC, and TGA and mechanically characterized via tensile testing and crimping. The addition of rubber improved the elasticity of PTCR (658 ± 68% for dry and 415 ± 45% for swollen films) significantly compared with its nonrubber-based citrate copolymer, i.e., poly(tetrahydrofuran-co-citrate) (PTC) (550 ± 51% for dry and 88 ± 10% for swollen films). Also, the mechanical strength of PTCR reached as high as 0.8 ± 0.06 MPa after the successful addition of rubber into PTC, which had a tensile strength of 0.55 ± 0.04 MPa. Notably, the 3D-printed vascular scaffold of mPTCR demonstrated excellent mechanical competence in crimping and expansion, which is necessary for clinical use. The percent diameter recovery of mPTCR vascular scaffolds (89.4 ± 1.1%) was higher than that of its nonrubber version, i.e., methacrylated-poly(tetrahydrofuran-co-citrate) (mPTC) (77.2 ± 6.7%), illustrating the contribution of rubber in mPTCR. In vitro degradation studies showed rapid hydrolytic degradation of the PTCR elastomer in 6 weeks, whereas 3D-printed scaffolds of mPTCR degraded slowly due to its improved stability after methacrylation. The cytocompatibility and cell attachment on the vascular scaffold surfaces were successfully demonstrated by using L929 mouse myoblasts. To conclude, this study reports a citrate-based rubber that should help meet some of the scaffold mechanical requirements for tissue-engineering applications.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PolyestersPrinting, Three-DimensionalRubberTissue EngineeringBiocompatible MaterialsCitric AcidTissue ScaffoldsElasticityTensile StrengthHumansAnimalsMiceElastomers

Stichwörter der Autor:innen

3D printablebiodegradablebiomaterialsbiopolymersnatural rubber

Substanzen

PolyestersRubberBiocompatible MaterialsCitric AcidElastomers

Autor:innen und Institutionen

  • Center for Advanced Regenerative Engineering (CARE), Northwestern University, Evanston, Illinois 60208, United States.
  • Department of Biomedical Engineering, Northwestern University, Evanston, Illinois 60208, United States.
  • Department of Mechanical Engineering, Northwestern University, Evanston, Illinois 60208, United States.
  • Department of Surgery, Feinberg School of Medicine, Northwestern University, Chicago, Illinois 60611, United States.
  • Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, Illinois 60208, United States.
  • Chemistry of Life Processes Institute, Northwestern University, Evanston, Illinois 60208, United States.

ORCID-Profile: Amir Khan, Cheng Sun, Guillermo A Ameer

Förderung

  • NIBIB NIH HHS
  • National Institutes of Health
  • Northwestern University

Zitieren

APA

Khan, A., Ding, Y., Fu, R., Wang, X., Mendez-Santos, M., Adepu, S., Sun, C., & Ameer, G. A. (2025). Highly Elastic, Biodegradable Polyester-Based Citrate Rubber for 3D Printing in Regenerative Engineering. ACS Biomaterials Science & Engineering. https://doi.org/10.1021/acsbiomaterials.4c01486

Vancouver

Khan A, Ding Y, Fu R, Wang X, Mendez-Santos M, Adepu S, et al. Highly Elastic, Biodegradable Polyester-Based Citrate Rubber for 3D Printing in Regenerative Engineering. ACS Biomaterials Science & Engineering. 2025. doi:10.1021/acsbiomaterials.4c01486

BibTeX
@article{Khan2025,
  author = {Khan, Amir and Ding, Yonghui and Fu, Rao and Wang, Xinlong and Mendez-Santos, Maria and Adepu, Shivakalyani and Sun, Cheng and Ameer, Guillermo A},
  title = {Highly Elastic, Biodegradable Polyester-Based Citrate Rubber for 3D Printing in Regenerative Engineering},
  journal = {ACS Biomaterials Science & Engineering},
  year = {2025},
  doi = {10.1021/acsbiomaterials.4c01486}
}
Kostenlos starten →