EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Automatic Photo-Cross-Linking System for Robotic-Based In Situ Bioprinting

Gabriele Maria Fortunato iD, Elisa Batoni, Ilenia Pasqua, Matteo Nicoletta, Giovanni Vozzi, Carmelo De Maria iD

ACS Biomaterials Science & Engineering · 11.12.2023 · 9 (12) · 6926-6934

DOI: 10.1021/acsbiomaterials.3c00898 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Biomaterials Science & Engineering, online erschienen am 12.10.2023. Verfasst von Gabriele Maria Fortunato und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Information Engineering and Research Centre "E. Piaggio", University of Pisa, 56122 Pisa, Italy. Hauptthemen laut MEDLINE: Bioprinting, Robotics, Robotic Surgical Procedures. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Commission, FoReLab, Crosslab Additive Manufacturing.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This work reports the design and validation of an innovative automatic photo-cross-linking device for robotic-based in situ bioprinting. Photo-cross-linking is the most promising polymerization technique when considering biomaterial deposition directly inside a physiological environment, typical of the in situ bioprinting approach. The photo-cross-linking device was designed for the IMAGObot platform, a 5-degree-of-freedom robot re-engineered for in situ bioprinting applications. The system consists of a syringe pump extrusion module equipped with eight light-emitting diodes (LEDs) with a 405 nm wavelength. The hardware and software of the robot were purposely designed to manage the LEDs switching on and off during printing. To minimize the light exposure of the needle, thus avoiding its clogging, only the LEDs opposite the printing direction are switched on to irradiate the newly deposited filament. Moreover, the LED system can be adjusted in height to modulate substrate exposure. Different scaffolds were bioprinted using a GelMA-based hydrogel, varying the printing speed and light distance from the bed, and were characterized in terms of swelling and mechanical properties, proving the robustness of the photo-cross-linking system in various configurations. The system was finally validated onto anthropomorphic phantoms (i.e., a human humerus head and a human hand with defects) featuring complex nonplanar surfaces. The designed system was successfully used to fill these anatomical defects, thus resulting in a promising solution for in situ bioprinting applications.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

BioprintingRoboticsRobotic Surgical ProceduresHumansTissue ScaffoldsTissue EngineeringPrinting, Three-DimensionalGelatin

Stichwörter der Autor:innen

automatic devicegelatin methacryloylphoto-cross-linkingrobotic-based in situ bioprinting

Substanzen

Gelatin

Autor:innen und Institutionen

  • Department of Information Engineering and Research Centre "E. Piaggio", University of Pisa, 56122 Pisa, Italy.

ORCID-Profile: Gabriele Maria Fortunato, Carmelo De Maria

Förderung

  • European Commission
  • FoReLab
  • Crosslab Additive Manufacturing

Zitieren

APA

Fortunato, G. M., Batoni, E., Pasqua, I., Nicoletta, M., Vozzi, G., & De Maria, C. (2023). Automatic Photo-Cross-Linking System for Robotic-Based In Situ Bioprinting. ACS Biomaterials Science & Engineering, 9(12), 6926-6934. https://doi.org/10.1021/acsbiomaterials.3c00898

Vancouver

Fortunato GM, Batoni E, Pasqua I, Nicoletta M, Vozzi G, De Maria C. Automatic Photo-Cross-Linking System for Robotic-Based In Situ Bioprinting. ACS Biomaterials Science & Engineering. 2023;9(12):6926-6934. doi:10.1021/acsbiomaterials.3c00898

BibTeX
@article{Fortunato2023,
  author = {Fortunato, Gabriele Maria and Batoni, Elisa and Pasqua, Ilenia and Nicoletta, Matteo and Vozzi, Giovanni and De Maria, Carmelo},
  title = {Automatic Photo-Cross-Linking System for Robotic-Based In Situ Bioprinting},
  journal = {ACS Biomaterials Science & Engineering},
  year = {2023},
  volume = {9},
  number = {12},
  pages = {6926--6934},
  doi = {10.1021/acsbiomaterials.3c00898}
}
Kostenlos starten →