EUVIMEDEUVIMED entdecken
Crossref

Wettability-Programmable Poly(vinyl alcohol)/Glutaraldehyde Hydrogel with Triple Network for 3D-Printed Monolithic Microfluidic Chips with Matched Water/Oil Transport

Di Liu, Ruoyu Zhang, Fei Zhai iD, Zhongying Ji iD, Xinyan Shi iD, Yang Lyu, Xiaolong Wang iD

ACS Applied Materials & Interfaces · 09.09.2026 · 18 (35) · 48286-48296

DOI: 10.1021/acsami.6c13837 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 26.08.2026. Verfasst von Di Liu und 6 weiteren Autor:innen. Beteiligte Einrichtung: Shandong Laboratory of Advanced Materials and Green Manufacturing at Yantai, Yantai Zhongke Research Institute of Advanced Materials and Green Chemic…. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 42 Literaturangaben. Gefördert von: Natural Science Foundation of Shandong Province, Taishan Scholar Project of Shandong Province, Shandong Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Conventional microfluidic chips fabricated from polydimethylsiloxane (PDMS), glass, and silicon suffer from intrinsically fixed surface wettability, tedious post-modification, and inhomogeneous wetting inside enclosed three-dimensional (3D) microchannels, which severely restrict their applications in biphasic fluid manipulation. Herein, we develop a photocurable poly(vinyl alcohol) (PVA)-based hydrogel featuring a triple synergistic network for digital light processing (DLP) 3D printing of integrated microfluidic devices. Under acidic catalysis, glutaraldehyde (GA) undergoes acetalization with PVA to form the first crosslinked network, which consumes hydrophilic hydroxyl groups and introduces hydrophobic alkyl segments. Subsequently, the hydrogel framework is co-constructed by a PVA hydrogen-bonding physical network and a UV-initiated covalent network derived from acrylamide (AAm), acrylic acid (AAc), and poly(ethylene glycol) diacrylate (PEGDA), ultimately yielding a triple-crosslinked network. By adjusting the GA loading, the water contact angle of the hydrogel can be continuously tuned from 15.42° (hydrophilic) to 111.66° (hydrophobic). Benefiting from the interpenetrating multi-network architecture, the tensile strength increases from 48.76 kPa to 118.27 kPa, and the elastic modulus increases from 14.72 to 63.84 kPa. DLP 3D printing enables the direct fabrication of monolithic microfluidic chips with smooth microchannels down to approximately 160 μm in width, without requiring any post-treatment. Fluorescence characterization confirms that the hydrophilic channels allow stable laminar flow of deionized water, while the hydrophobic channels enable low-friction transport of mineral oil. This work establishes a comprehensive strategy integrating molecular design, wettability programming, and 3D additive manufacturing, providing a scalable platform for applications in fluid transportation, biochemical detection, environmental monitoring, and wearable microfluidics.

Schlagwörter

Stichwörter der Autor:innen

digital light processing 3D printingfluid transportmicrofluidic chippolyvinyl alcohol hydrogelwettability programming

Autor:innen und Institutionen

  • Shandong Laboratory of Advanced Materials and Green Manufacturing at Yantai, Yantai Zhongke Research Institute of Advanced Materials and Green Chemical Engineering, Yantai264006, China.
  • Key Laboratory of Rubber & Plastics, Ministry of Education, School of Polymer Science and Engineering, Qingdao University of Science & Technology, Qingdao266042, China.
  • State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou730000, China.
  • Zibo Municipal General Institute of Inspection and Metrology, Zibo255100, China.

ORCID-Profile: Fei Zhai, Zhongying Ji, Xinyan Shi, Xiaolong Wang

Förderung

  • Natural Science Foundation of Shandong Province
  • Taishan Scholar Project of Shandong Province
  • Shandong Province
  • Tianjin Science and Technology Program Project
  • Special Supporting Project for Provincial Leading Talents of Yantai
  • National Basic Research Program of China (973 Program)
  • Gansu Province

Zitieren

APA

Liu, D., Zhang, R., Zhai, F., Ji, Z., Shi, X., Lyu, Y., & Wang, X. (2026). Wettability-Programmable Poly(vinyl alcohol)/Glutaraldehyde Hydrogel with Triple Network for 3D-Printed Monolithic Microfluidic Chips with Matched Water/Oil Transport. ACS Applied Materials & Interfaces, 18(35), 48286-48296. https://doi.org/10.1021/acsami.6c13837

Vancouver

Liu D, Zhang R, Zhai F, Ji Z, Shi X, Lyu Y, et al. Wettability-Programmable Poly(vinyl alcohol)/Glutaraldehyde Hydrogel with Triple Network for 3D-Printed Monolithic Microfluidic Chips with Matched Water/Oil Transport. ACS Applied Materials & Interfaces. 2026;18(35):48286-48296. doi:10.1021/acsami.6c13837

BibTeX
@article{Liu2026,
  author = {Liu, Di and Zhang, Ruoyu and Zhai, Fei and Ji, Zhongying and Shi, Xinyan and Lyu, Yang and Wang, Xiaolong},
  title = {Wettability-Programmable Poly(vinyl alcohol)/Glutaraldehyde Hydrogel with Triple Network for 3D-Printed Monolithic Microfluidic Chips with Matched Water/Oil Transport},
  journal = {ACS Applied Materials & Interfaces},
  year = {2026},
  volume = {18},
  number = {35},
  pages = {48286--48296},
  doi = {10.1021/acsami.6c13837}
}
Kostenlos starten →