Interface-Engineered Thermoplastic Polyurethane/Ethylene-Propylene-Diene Monomer Composite Foams for Durable Silicon Carbide Polishing Pads
ACS Applied Materials & Interfaces · 05.08.2026 · 18 (30) · 41806-41822
DOI: 10.1021/acsami.6c10511 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 22.07.2026. Verfasst von Xuwei Li und 5 weiteren Autor:innen. Beteiligte Einrichtung: State Key Laboratory of Chemical Engineering and Low-Carbon Technology, Shanghai Key Laboratory of Multiphase Materials Chemical Engineering, School …. Die Arbeit nennt 60 Literaturangaben. Gefördert von: China Association for Science and Technology, Ministry of Education of the People's Republic of China, China Scholarship Council.
Abstract (Originalsprache)
Chemical mechanical polishing (CMP) of silicon carbide (SiC) operates under simultaneous mechanical loading and strong oxidative environments, placing stringent demands on polishing pad materials. High-hardness thermoplastic polyurethane (TPU), although widely employed, exhibits insufficient compliance, localized stress accumulation, and vulnerability to fatigue damage during prolonged operation. Meanwhile, the tribological response of polymer composites under such coupled mechanical-oxidative conditions remains insufficiently understood. Here, ethylene-propylene-diene monomer (EPDM) was introduced to modify high-hardness TPU, while interfacial compatibility and structural robustness were tailored using maleic anhydride grafted EPDM (EPDM-g-MAH) and irradiation-induced network formation. Microcellular foams with similar expansion ratios and cell sizes were prepared using supercritical carbon dioxide (CO2) foaming, enabling a systematic assessment of their wear and tribological performance. The modified systems exhibit improved wear resistance, as evidenced by reduced material loss and suppressed damage evolution compared to neat TPU. Notably, the introduction of microcellular architecture leads to an environment-dependent trade-off effect: while the reduced load-bearing capacity deteriorates wear resistance under nonoxidative conditions, the cellular structure enhances durability in oxidative environments by restricting the penetration of reactive species. The tribological response is governed by the combined influence of phase organization, interfacial cohesion, and network constraints, which together contribute to more stable sliding behavior. Improved resistance to thermal perturbation further contributes to maintaining functional integrity during sliding. These findings clarify the interplay between interfacial design and structural architecture, providing an interface-controlled design strategy for developing advanced polymer-based composite polishing materials for SiC CMP applications.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- State Key Laboratory of Chemical Engineering and Low-Carbon Technology, Shanghai Key Laboratory of Multiphase Materials Chemical Engineering, School of Chemical Engineering, East China University of Science and Technolo…
- Shanghai Electronic Chemicals Innovation Institute, East China University of Science and Technology, Shanghai201419, PR China.
ORCID-Profile: Yichong Chen, Dongdong Hu, Ling Zhao
Förderung
- China Association for Science and Technology
- Ministry of Education of the People's Republic of China
- China Scholarship Council
- Fundamental Research Funds for the Central Universities
- Higher Education Discipline Innovation Project
- National Natural Science Foundation of China (NSFC)
Zitieren
APA
Li, X., Chen, Y., Sun, J., Cao, Y., Hu, D., & Zhao, L. (2026). Interface-Engineered Thermoplastic Polyurethane/Ethylene-Propylene-Diene Monomer Composite Foams for Durable Silicon Carbide Polishing Pads. ACS Applied Materials & Interfaces, 18(30), 41806-41822. https://doi.org/10.1021/acsami.6c10511
Vancouver
Li X, Chen Y, Sun J, Cao Y, Hu D, Zhao L. Interface-Engineered Thermoplastic Polyurethane/Ethylene-Propylene-Diene Monomer Composite Foams for Durable Silicon Carbide Polishing Pads. ACS Applied Materials & Interfaces. 2026;18(30):41806-41822. doi:10.1021/acsami.6c10511
BibTeX
@article{Li2026,
author = {Li, Xuwei and Chen, Yichong and Sun, Jiayang and Cao, Yulian and Hu, Dongdong and Zhao, Ling},
title = {Interface-Engineered Thermoplastic Polyurethane/Ethylene-Propylene-Diene Monomer Composite Foams for Durable Silicon Carbide Polishing Pads},
journal = {ACS Applied Materials & Interfaces},
year = {2026},
volume = {18},
number = {30},
pages = {41806--41822},
doi = {10.1021/acsami.6c10511}
}
EUVIMED