Polymer Coating Adhesion Drives Functional and Biological Outcomes in Meniscus Implants
ACS Applied Materials & Interfaces · 2026
DOI: 10.1021/acsami.6c10220 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, 2026. Verfasst von Alfonso F Blanco und 9 weiteren Autor:innen. Beteiligte Einrichtung: University of Santiago de Compostela, Center for Research in Molecular Medicine and Chronic Diseases (CiMUS), Health Research Institute of Santiago d…. Hauptthemen laut MEDLINE: Polymers, Coated Materials, Biocompatible, Meniscus, Prostheses and Implants. Die Arbeit nennt 64 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: H2020 LEIT Advanced Materials, Ministerio de Ciencia, Innovación y Universidades, Instituto de Salud Carlos III.
Abstract (Originalsprache)
Achieving stable integration of drug-releasing polymer coatings with load-bearing meniscus implants remains a challenge in biomaterials engineering. In this study, four surface modification strategies, femtosecond-pulsed laser treatment, oxygen plasma, polydopamine, and an ethyl-2-cyanoacrylate (ECA) interlayer, were evaluated for the integration of a dexamethasone (DEX)- and celecoxib (CLX)-releasing bilayer coating with a polycarbonate urethane (PCU) meniscus implant. The selected construct comprised an ECA interlayer applied from a 40% (w/v) solution, a CLX-loaded PLLA/PCL layer prepared at 100 mg/mL and a 53/47 (w/w) polymer ratio with 16.6% CLX loading, and an outer DEX-loaded PLGA layer prepared at 200 mg/mL with 2.44% DEX loading. At 37 °C, compared with uncoated PCU, ECA-containing constructs showed significantly higher storage modulus, loss modulus, and elastic modulus (p < 0.05), while tan δ remained unchanged, indicating preservation of the elastic-dominant viscoelastic response of the complete construct. The ECA-containing coating was subsequently adapted to the geometry of a sheep meniscus implant using an optimized dip-coating procedure. During a 21-day bioreactor study, repeated compression and shear increased cumulative DEX release from 59 to 67% and CLX release from 25 to 40% relative to static controls, while no visible coating delamination was observed. Ethylene oxide sterilization preserved drug loading and release behavior. In an exploratory three-month sheep study, the fiber-fixed coated implants remained in position, and the coating remained macroscopically associated with the retrieved prostheses. These findings support the use of an ECA interlayer to integrate a bilayer drug-releasing coating with a PCU meniscus implant while preserving construct-level mechanical behavior and drug release under the conditions evaluated.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- University of Santiago de Compostela, Center for Research in Molecular Medicine and Chronic Diseases (CiMUS), Health Research Institute of Santiago de Compostela (IDIS), Santiago de Compostela15706, Spain.
- Department of Pharmacy and Pharmaceutical Technology, Faculty of Pharmacy, University of Santiago de Compostela, Santiago de Compostela15705, Spain.
- University of Santiago de Compostela, Photonics4Life Group, Faculty of Physics and Faculty of Optics and Optometry, Materials Institute (iMATUS), Santiago de Compostela15782, Spain.
- University of A Coruña, Industrial Campus, CITENI-Polymers Group, Ferrol15403, Spain.
- Cellular and Molecular Cardiology Research Unit, IDIS, Complexo Hospitalario Universitario de Santiago de Compostela, Área Sanitaria Santiago de Compostela e Barbanza (SERGAS), Santiago de Compostela15706, Spain.
- Department of Orthopedics, University Medical Center Utrecht, Utrecht3584 CX, The Netherlands.
ORCID-Profile: Carmen Bao-Varela, Jos Malda, María José Alonso
Förderung
- H2020 LEIT Advanced Materials
- Ministerio de Ciencia, Innovación y Universidades
- Instituto de Salud Carlos III
- Consellería de Cultura, Educación e Ordenación Universitaria, Xunta de Galicia
- European Regional Development Fund
- Ministerio de Ciencia, Innovaci?n y Universidades
- Conseller?a de Cultura, Educaci?n e Ordenaci?n Universitaria, Xunta de Galicia
Zitieren
APA
Blanco, A. F., Rubio-Prego, I., Bao-Varela, C., Bouza, R., Nuñez Bernal, P., Levato, R., Malda, J., Kon, E., Crecente-Campo, J., & Alonso, M. J. (2026). Polymer Coating Adhesion Drives Functional and Biological Outcomes in Meniscus Implants. ACS Applied Materials & Interfaces. https://doi.org/10.1021/acsami.6c10220
Vancouver
Blanco AF, Rubio-Prego I, Bao-Varela C, Bouza R, Nuñez Bernal P, Levato R, et al. Polymer Coating Adhesion Drives Functional and Biological Outcomes in Meniscus Implants. ACS Applied Materials & Interfaces. 2026. doi:10.1021/acsami.6c10220
BibTeX
@article{Blanco2026,
author = {Blanco, Alfonso F and Rubio-Prego, Inés and Bao-Varela, Carmen and Bouza, Rebeca and Nuñez Bernal, Paulina and Levato, Riccardo and Malda, Jos and Kon, Elizaveta and Crecente-Campo, José and Alonso, María José},
title = {Polymer Coating Adhesion Drives Functional and Biological Outcomes in Meniscus Implants},
journal = {ACS Applied Materials & Interfaces},
year = {2026},
doi = {10.1021/acsami.6c10220}
}
EUVIMED