Doping, Alloying, or Compositing? How Copper Introduction Pathways Dictate Thermoelectric Performance in GeTe
ACS Applied Materials & Interfaces · 01.07.2026 · 18 (25) · 35711-35720
DOI: 10.1021/acsami.6c09295 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 15.06.2026. Verfasst von Yang Li und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Materials Science and Engineering, Shanghai University, 99 Shangda Road, Shanghai 200444, China. Die Arbeit nennt 53 Literaturangaben. Gefördert von: National Natural Science Foundation of China.
Abstract (Originalsprache)
The thermoelectric performance of GeTe is critically governed not only by the choice of dopant but also by the pathway through which it is introduced. Herein, we systematically compare three distinct Cu introduction routes in a Ge 0.95 Bi 0.05 Te matrix: direct Cu doping, BaCu 2 Te 2 alloying, and BaCu 2 Te 2 compositing. All three approaches effectively reduce the excessively high hole concentration, thereby decreasing electrical conductivity and increasing the Seebeck coefficient. However, they exhibit markedly different regulation mechanisms. Direct Cu doping achieves the most pronounced reduction in carrier concentration and optimizes carrier mobility but yields only a moderate improvement in the dimensionless thermoelectric figure of merit zT (∼1.86) due to limited phonon scattering. In contrast, the compositing strategy allows limited Cu diffusion into the matrix, while Ba induces additional Ge vacancies that partially compensate for the carrier reduction. The secondary phase introduces strong carrier scattering, suppressing carrier mobility, and also significantly enhances the density-of-states effective mass and reduces lattice thermal conductivity. Consequently, the Ge 0.95 Bi 0.05 Te + 2.0 wt % BaCu 2 Te 2 composite attains a peak zT exceeding 2.0 at 623 K. BaCu 2 Te 2 alloying exhibits intermediate behavior, with more Cu incorporation and stronger vacancy compensation, also achieving a zT near 2.0. This work demonstrates that the Cu introduction pathway dictates the balance between carrier concentration modulation, mobility preservation, effective mass enhancement, and phonon scattering, providing a paradigm for synergistically integrating doping and secondary-phase engineering in GeTe-based thermoelectrics.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Materials Science and Engineering, Shanghai University, 99 Shangda Road, Shanghai 200444, China.
- School of Physics and Materials Science, Guangzhou University, Guangzhou 510006, China.
- Interdisciplinary Materials Research Center, School of Materials Science and Engineering, Tongji University, Shanghai 201804, China.
ORCID-Profile: Jiye Zhang, Kai Guo, Jun Luo
Förderung
- National Natural Science Foundation of China
Zitieren
APA
Li, Y., Zhang, Y., Zhang, Y., Wang, S., Zhang, J., Guo, K., & Luo, J. (2026). Doping, Alloying, or Compositing? How Copper Introduction Pathways Dictate Thermoelectric Performance in GeTe. ACS Applied Materials & Interfaces, 18(25), 35711-35720. https://doi.org/10.1021/acsami.6c09295
Vancouver
Li Y, Zhang Y, Zhang Y, Wang S, Zhang J, Guo K, et al. Doping, Alloying, or Compositing? How Copper Introduction Pathways Dictate Thermoelectric Performance in GeTe. ACS Applied Materials & Interfaces. 2026;18(25):35711-35720. doi:10.1021/acsami.6c09295
BibTeX
@article{Li2026,
author = {Li, Yang and Zhang, Yunpu and Zhang, Yuting and Wang, Shaoqin and Zhang, Jiye and Guo, Kai and Luo, Jun},
title = {Doping, Alloying, or Compositing? How Copper Introduction Pathways Dictate Thermoelectric Performance in GeTe},
journal = {ACS Applied Materials & Interfaces},
year = {2026},
volume = {18},
number = {25},
pages = {35711--35720},
doi = {10.1021/acsami.6c09295}
}
EUVIMED