Nitrocellulose-Based Membranes for Electrocatalytic Bicarbonate-to-Formate Conversion via In Situ Generated CO2
ACS Applied Materials & Interfaces · 05.08.2026 · 18 (30) · 40964-40974
DOI: 10.1021/acsami.6c08711 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 21.07.2026. Verfasst von Fumiaki Amano und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Applied Chemistry for Environment, Tokyo Metropolitan University, 1-1 Minami-Osawa, Hachioji, Tokyo192-0397, Japan. Die Arbeit nennt 46 Literaturangaben. Gefördert von: Tokyo Metropolitan Government, New Energy and Industrial Technology Development Organization.
Abstract (Originalsprache)
CO2 conversion using aqueous carbonate and bicarbonate solutions is a promising route for reactive CO2 capture, but sustaining high Faradaic efficiency (FE) over a broad pH range remains challenging. Introducing a mixed cellulose ester (MCE) porous membrane between the proton exchange membrane (PEM) and the bismuth cathode electrocatalyst enhances the FE for formate production during bicarbonate-fed electrolysis. In this configuration, bicarbonate ions (HCO3–) are protonated within the electrolyzer, enabling direct utilization of in situ–generated CO2 (i-CO2) for electroreduction. Here, we investigate the role of the intermediate porous membrane and the effects of different cellulose materials on electrolysis performance at current densities above 100 mA cm–2. Although direct contact between the cathode and PEM significantly decreases formate FE with increasing pH, incorporating the MCE membrane enhanced formate FE across all pH values, maintaining 78% even at pH 9.2 (2.0 mol L–1 KHCO3 + 0.5 mol L–1 K2CO3), demonstrating its effectiveness in sustaining i-CO2 generation. In contrast, α-cellulose and acetyl cellulose exhibit lower formate FE and higher full-cell voltage owing to increased cell resistance. Operando electrochemical impedance spectroscopy and real-time visualization of the bubble formation reveal that these celluloses produced large CO2 bubbles, whereas i-CO2 remained predominantly dissolved when using the MCE membrane, which is mainly composed of nitrocellulose. These results indicate that nitrate ester groups facilitate i-CO2 generation and its transport to the cathode catalyst. Furthermore, a 3.0 mol L–1 KOH solution that captures CO2 gas achieves 91% formate FE at 100 mA cm–2, with a full-cell voltage of 1.5 V and 80% i-CO2 utilization, highlighting the potential of this MCE-based electrolyzer design for reactive CO2 capture and utilization.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Applied Chemistry for Environment, Tokyo Metropolitan University, 1-1 Minami-Osawa, Hachioji, Tokyo192-0397, Japan.
- Research Center for Hydrogen Energy-Based Society, Tokyo Metropolitan University, 1-1 Minami-Osawa, Hachioji, Tokyo192-0397, Japan.
- Faculty of Mechanical Engineering, Institute of Science and Engineering, Kanazawa University, Kakuma-machi, Kanazawa, Ishikawa920-1192, Japan.
ORCID-Profile: Fumiaki Amano, Takuya Okazaki, Tetsuya Shishido
Förderung
- Tokyo Metropolitan Government
- New Energy and Industrial Technology Development Organization
Zitieren
APA
Amano, F., Nomoto, K., Okazaki, T., Higashino, S., Watanabe, S., Tsujiguchi, T., & Shishido, T. (2026). Nitrocellulose-Based Membranes for Electrocatalytic Bicarbonate-to-Formate Conversion via In Situ Generated CO2. ACS Applied Materials & Interfaces, 18(30), 40964-40974. https://doi.org/10.1021/acsami.6c08711
Vancouver
Amano F, Nomoto K, Okazaki T, Higashino S, Watanabe S, Tsujiguchi T, et al. Nitrocellulose-Based Membranes for Electrocatalytic Bicarbonate-to-Formate Conversion via In Situ Generated CO2. ACS Applied Materials & Interfaces. 2026;18(30):40964-40974. doi:10.1021/acsami.6c08711
BibTeX
@article{Amano2026,
author = {Amano, Fumiaki and Nomoto, Kohta and Okazaki, Takuya and Higashino, Shinichiro and Watanabe, Soyoka and Tsujiguchi, Takuya and Shishido, Tetsuya},
title = {Nitrocellulose-Based Membranes for Electrocatalytic Bicarbonate-to-Formate Conversion via In Situ Generated CO2},
journal = {ACS Applied Materials & Interfaces},
year = {2026},
volume = {18},
number = {30},
pages = {40964--40974},
doi = {10.1021/acsami.6c08711}
}
EUVIMED