EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Speed Matters: Standardizing Mechanical Testing Conditions for Contact–Separation Triboelectric Nanogenerators

Artis Linarts iD, Delong He iD, Peter C Sherrell iD, Robert Komljenovic iD, Anna Šutka, Kaspars Malnieks iD, Hanlu Zhang, Dumindu Dassanayaka iD, Amgad R Rezk iD, Jinbo Bai iD, Andris Šutka iD

ACS Applied Materials & Interfaces · 16.09.2026 · 18 (36) · 48933-48945

DOI: 10.1021/acsami.6c07808 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 03.09.2026. Verfasst von Artis Linarts und 10 weiteren Autor:innen. Beteiligte Einrichtung: Centre of Excellence for Future Assistive Technologies, Faculty of Natural Sciences and Technology, Riga Technical University, Paula Valdena 3/7, LV-…. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 75 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: RMIT University, Central Finance and Contracting Agency.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Triboelectric nanogenerators (TENGs) are a key emerging technology for powering wearable, implantable, remote, and autonomous small-scale electronics. Despite extensive reports, there is often a lack of rigor in reporting the mechanical testing conditions used to measure electrical performance in TENGs. Herein, we systematically vary the separation speed in contact–separation TENGs between 12.5 and 700 mm s–1 (both experimentally and via simulations) and measure a corresponding increase in power density from 10–7 to 10–4 W (along with analogous increases in measured current and voltage)-without changing any other material property or parameter. The transferred charge density (on the external electrodes, as separate from the surface charge density) also increased from 0.3 to 10 nC cm–2, demonstrating (along with supporting computational simulation experiments) that large changes in measured output can arise from testing conditions rather than changes in material chemistry or device structure. These results demonstrate the importance of separation speed in contextualizing literature reports of TENG performance and highlight the need to dramatically improve data reporting for the field. To address this, we propose the need to report a standard and consistent set of testing parameters for contact separation. Adoption of these conditions will enable meaningful benchmarking of TENGs and allow the field to progress more effectively.

Schlagwörter

Stichwörter der Autor:innen

TENGscontact electrificationmechanical energy conversionmetrologysimulations

Autor:innen und Institutionen

  • Centre of Excellence for Future Assistive Technologies, Faculty of Natural Sciences and Technology, Riga Technical University, Paula Valdena 3/7, LV-1048Riga, Latvia.
  • Université Paris-Saclay, CentraleSupélec, ENS Paris-Saclay, CNRS, LMPS-Laboratoire de Mécanique Paris-Saclay, 91190Gif-sur-Yvette, France.
  • School of Science, RMIT University, Melbourne3001, Australia.
  • Micro/Nanophysics Research Laboratory, School of Engineering, RMIT University, Melbourne, VIC3001, Australia.
  • Institute of Physics and Materials Science, Faculty of Natural Sciences and Technology, Riga Technical University, LV-1048Riga, Latvia.
  • Henan International Joint Laboratory of Nano-Photoelectric Magnetic Materials, Henan University of Technology, Zhengzhou450001, China.

ORCID-Profile: Artis Linarts, Delong He, Peter C Sherrell, Robert Komljenovic, Kaspars Malnieks, Dumindu Dassanayaka, Amgad R Rezk, Jinbo Bai, Andris Šutka

Förderung

  • RMIT University
  • Central Finance and Contracting Agency

Zitieren

APA

Linarts, A., He, D., Sherrell, P. C., Komljenovic, R., Šutka, A., Malnieks, K., Zhang, H., Dassanayaka, D., Rezk, A. R., Bai, J., & Šutka, A. (2026). Speed Matters: Standardizing Mechanical Testing Conditions for Contact–Separation Triboelectric Nanogenerators. ACS Applied Materials & Interfaces, 18(36), 48933-48945. https://doi.org/10.1021/acsami.6c07808

Vancouver

Linarts A, He D, Sherrell PC, Komljenovic R, Šutka A, Malnieks K, et al. Speed Matters: Standardizing Mechanical Testing Conditions for Contact–Separation Triboelectric Nanogenerators. ACS Applied Materials & Interfaces. 2026;18(36):48933-48945. doi:10.1021/acsami.6c07808

BibTeX
@article{Linarts2026,
  author = {Linarts, Artis and He, Delong and Sherrell, Peter C and Komljenovic, Robert and Šutka, Anna and Malnieks, Kaspars and Zhang, Hanlu and Dassanayaka, Dumindu and Rezk, Amgad R and Bai, Jinbo and Šutka, Andris},
  title = {Speed Matters: Standardizing Mechanical Testing Conditions for Contact–Separation Triboelectric Nanogenerators},
  journal = {ACS Applied Materials & Interfaces},
  year = {2026},
  volume = {18},
  number = {36},
  pages = {48933--48945},
  doi = {10.1021/acsami.6c07808}
}
Kostenlos starten →