EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

High Operating Potential Induces Conversion in Li-Rich Chalcogenides

Abhiroop Mishra iD, Victoria K Davis, Nicholas V Dulock iD, Eshaan S Patheria iD, Nathan F Dalleska iD, Kimberly A See iD

ACS Applied Materials & Interfaces · 15.07.2026 · 18 (27) · 37724-37732

DOI: 10.1021/acsami.6c06453 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 06.07.2026. Verfasst von Abhiroop Mishra und 5 weiteren Autor:innen. Beteiligte Einrichtung: Division of Chemistry and Chemical Engineering, California Institute of Technology, Pasadena, California 91125, United States. Die Arbeit nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Division of Materials Research.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

High Resolution Image Download MS PowerPoint Slide Lithium-ion batteries are central to the renewable energy transition, yet the capacity of commercial cathode materials limits further improvement in performance. Li-rich cathodes offer a promising route to higher capacities by leveraging both cationic and anionic redox. However, the full theoretical capacity is yet to be realized in the Li-rich materials. Here, we evaluate conditions to attempt full delithiation, which requires higher operating potentials. We focus on the Li-rich sulfide and selenide Li 2 FeCh 2 (Ch = S, Se), since high potential required to access anion redox in oxides leads to severe degradation of electrolyte which obscures intrinsic cathode processes. Both materials exhibit poor Coulombic efficiency and rapid capacity loss during galvanostatic measurements that reach >3 V vs Li/Li + . The materials undergo conversion reactions at these potentials, which is corroborated by ex situ laser ablation inductively coupled plasma mass spectrometry (ICP-MS) and X-ray diffraction (XRD) measurements. For Li 2 FeS 2, conversion to polysulfides causes material loss. However, if the upper voltage cutoff is below 3 V vs Li/Li +, there is no evidence of dissolved S even though persulfides are formed in the solid Li 2– x FeS 2 . In contrast, conversion of Li 2 FeSe 2 to γ-Se is limited to the solid-state, though formation of protons via electrolyte decomposition causes active-material dissolution. The conversion reactions occur >1 V positive of the reversible anion redox reactions in both materials which makes it easy to avoid such parasitic side reactions by potential limited cycling.

Schlagwörter

Stichwörter der Autor:innen

Li-ion batteryLi-rich chalcogenidesactive-material lossconversion reactionpolysulfides

Autor:innen und Institutionen

  • Division of Chemistry and Chemical Engineering, California Institute of Technology, Pasadena, California 91125, United States.
  • Division of Geological and Planetary Science, California Institute of Technology, Pasadena, California 91125, United States.

ORCID-Profile: Abhiroop Mishra, Nicholas V Dulock, Eshaan S Patheria, Nathan F Dalleska, Kimberly A See

Förderung

  • Division of Materials Research

Zitieren

APA

Mishra, A., Davis, V. K., Dulock, N. V., Patheria, E. S., Dalleska, N. F., & See, K. A. (2026). High Operating Potential Induces Conversion in Li-Rich Chalcogenides. ACS Applied Materials & Interfaces, 18(27), 37724-37732. https://doi.org/10.1021/acsami.6c06453

Vancouver

Mishra A, Davis VK, Dulock NV, Patheria ES, Dalleska NF, See KA. High Operating Potential Induces Conversion in Li-Rich Chalcogenides. ACS Applied Materials & Interfaces. 2026;18(27):37724-37732. doi:10.1021/acsami.6c06453

BibTeX
@article{Mishra2026,
  author = {Mishra, Abhiroop and Davis, Victoria K and Dulock, Nicholas V and Patheria, Eshaan S and Dalleska, Nathan F and See, Kimberly A},
  title = {High Operating Potential Induces Conversion in Li-Rich Chalcogenides},
  journal = {ACS Applied Materials & Interfaces},
  year = {2026},
  volume = {18},
  number = {27},
  pages = {37724--37732},
  doi = {10.1021/acsami.6c06453}
}
Kostenlos starten →