EUVIMEDEUVIMED entdecken
Übersichtsarbeit

Relationship between Silicon Percentage in Graphite Anode to Achieve High-Energy-Density Lithium-Ion Batteries

Manoj Gautam iD, Govind Kumar Mishra iD, K Bhawana, Chhotelal Sah Kalwar, Deeksha Dwivedi, Anshu Yadav, Sagar Mitra iD

ACS Applied Materials & Interfaces · 04.09.2024 · 16 (35) · 45809-45820

DOI: 10.1021/acsami.4c10178 ↗

Kurz gefasst

Übersichtsarbeit in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 22.08.2024. Verfasst von Manoj Gautam und 6 weiteren Autor:innen. Beteiligte Einrichtung: Electrochemical Energy Storage Laboratory, Department of Energy Science and Engineering, Indian Institute of Technology Bombay, Powai, Mumbai 400076,…. Die Arbeit wurde bisher 51-mal zitiert (Crossref) und nennt 56 Literaturangaben. Gefördert von: Science and Engineering Research Board.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

High-weight-percentage silicon (Si) in graphite (Gr) anodes face commercialization hurdles due to fundamental and interrelated challenges. Nevertheless, using the existing manufacturing line, the optimized Si/Gr ratio is the most efficient and valuable way to fabricate high-energy-density lithium-ion batteries (LIBs). Still, literature has not thoroughly examined the Si/Gr ratio. This study addresses this critical gap by systematically evaluating Si content (5-20 wt %) in commercial graphite. The goal is to optimize the Si/Gr ratio for exceptional specific capacity while mitigating inherent Si limitations like cyclic stability and first-cycle irreversible capacity loss. This work employs a multidirectional approach, including in situ electrochemical impedance spectroscopy for interface analysis, rate capability assessment (up to 3 C-rate), Li diffusion coefficient measurement, and thorough cyclic stability evaluation. Increasing the silicon (Si) weight percent from 10% to 15% in the Si15Gr75 composite anode resulted in significant improvements in the first lithiation and delithiation capacities by approximately 16.8% and 16.0%, respectively. The Si15Gr75 cell delivered a high initial Coulombic efficiency of roughly 82.9%, nearly equivalent to a pure graphite anode. Furthermore, the Si15Gr75 Li cell exhibited excellent cyclic stability at a current rate of 0.5 C, retaining about 60% of its capacity after 215 cycles. Additionally, full-cell testing against a commercial NMC622 cathode showcases excellent performance across various current rates (0.1-0.5 C). This study paves the way for the development of high-energy-density LIBs by providing valuable insights into the optimization of Si/Gr composite anodes for commercial viability.

Schlagwörter

Stichwörter der Autor:innen

Diffusion CoefficientFull-Cell StudyInitial Coulombic EfficiencyRate CapabilitySilicon−Graphite

Autor:innen und Institutionen

  • Electrochemical Energy Storage Laboratory, Department of Energy Science and Engineering, Indian Institute of Technology Bombay, Powai, Mumbai 400076, India.

ORCID-Profile: Manoj Gautam, Govind Kumar Mishra, Sagar Mitra

Förderung

  • Science and Engineering Research Board

Zitieren

APA

Gautam, M., Mishra, G. K., Bhawana, K., Kalwar, C. S., Dwivedi, D., Yadav, A., & Mitra, S. (2024). Relationship between Silicon Percentage in Graphite Anode to Achieve High-Energy-Density Lithium-Ion Batteries. ACS Applied Materials & Interfaces, 16(35), 45809-45820. https://doi.org/10.1021/acsami.4c10178

Vancouver

Gautam M, Mishra GK, Bhawana K, Kalwar CS, Dwivedi D, Yadav A, et al. Relationship between Silicon Percentage in Graphite Anode to Achieve High-Energy-Density Lithium-Ion Batteries. ACS Applied Materials & Interfaces. 2024;16(35):45809-45820. doi:10.1021/acsami.4c10178

BibTeX
@article{Gautam2024,
  author = {Gautam, Manoj and Mishra, Govind Kumar and Bhawana, K and Kalwar, Chhotelal Sah and Dwivedi, Deeksha and Yadav, Anshu and Mitra, Sagar},
  title = {Relationship between Silicon Percentage in Graphite Anode to Achieve High-Energy-Density Lithium-Ion Batteries},
  journal = {ACS Applied Materials & Interfaces},
  year = {2024},
  volume = {16},
  number = {35},
  pages = {45809--45820},
  doi = {10.1021/acsami.4c10178}
}
Kostenlos starten →