Nonconductive Metal Oxide Gas Diffusion Layer for Mitigating Electrowetting during CO 2 Electrolysis
ACS Applied Materials & Interfaces · 05.06.2024 · 16 (22) · 28731-28741
DOI: 10.1021/acsami.4c05467 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 23.05.2024. Verfasst von Robert Haaring und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology, Daejeon 34141, South Korea. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 49 Literaturangaben. Gefördert von: National Research Foundation of Korea, Saudi Aramco-KAIST CO2 Management Center.
Abstract (Originalsprache)
Gas diffusion electrodes (GDEs) are extensively used for high current density electrochemical CO2 electrolysis (ECO2R), enabled by significantly reducing mass transfer resistance of CO2 to the catalyst layer. Conventionally, these GDEs are based upon hydrophobic carbon-based gas-diffusion layers (GDLs) that facilitate the gas transport; however, these supports are prone to flood with electrolyte during electrolysis. This potential-induced flooding, known as electrowetting, is related to the inherent conductivity of carbon and limits the activity of ECO2R. To investigate the effect of electrical conductivity more carefully, a GDE is constructed based on a Cu mesh with a nonconductive microporous GDL applied to this substrate, the latter composed of a mixture of metal oxide and polytetrafluoroethylene. With alumina as the metal oxide, a stable operation is obtained at -200 mA cm-2 with 70% selectivity for ECO2R (with over half toward C2+ products) without flooding as observed by in situ microscopy. On the contrary, with a Vulcan carbon-based GDL, the initial activity is rapidly lost as severe flooding ensues. It is reasoned that electrowetting is averted by virtue of the nonconductive nature of alumina, providing a new perspective on alternative GDL compositions and their influence on ECO2R performance.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology, Daejeon 34141, South Korea.
ORCID-Profile: Robert Haaring, Hyunjoo Lee
Förderung
- National Research Foundation of Korea
- Saudi Aramco-KAIST CO2 Management Center
Zitieren
APA
Haaring, R., Kang, P. W., Lee, J. W., Lee, J., & Lee, H. (2024). Nonconductive Metal Oxide Gas Diffusion Layer for Mitigating Electrowetting during CO 2 Electrolysis. ACS Applied Materials & Interfaces, 16(22), 28731-28741. https://doi.org/10.1021/acsami.4c05467
Vancouver
Haaring R, Kang PW, Lee JW, Lee J, Lee H. Nonconductive Metal Oxide Gas Diffusion Layer for Mitigating Electrowetting during CO 2 Electrolysis. ACS Applied Materials & Interfaces. 2024;16(22):28731-28741. doi:10.1021/acsami.4c05467
BibTeX
@article{Haaring2024,
author = {Haaring, Robert and Kang, Phil Woong and Lee, Jae Won and Lee, Junpyo and Lee, Hyunjoo},
title = {Nonconductive Metal Oxide Gas Diffusion Layer for Mitigating Electrowetting during CO 2 Electrolysis},
journal = {ACS Applied Materials & Interfaces},
year = {2024},
volume = {16},
number = {22},
pages = {28731--28741},
doi = {10.1021/acsami.4c05467}
}
EUVIMED