EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Direct Writing of a Titania Foam in Microgravity for Photocatalytic Applications

G Jacob Cordonier iD, Kyleigh Anderson, Ronan Butts, Ross O'Hara, Renee Garneau, Nathanael Wimer, John M Kuhlman, Konstantinos A Sierros iD

ACS Applied Materials & Interfaces · 11.10.2023 · 15 (40) · 47745-47753

DOI: 10.1021/acsami.3c09658 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 28.09.2023. Verfasst von G Jacob Cordonier und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Aerospace Engineering, West Virginia University, Morgantown, West Virginia 26506, United States. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 55 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Department of Mechanical and Aerospace Engineering, West Virginia University, National Aeronautics and Space Administration.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This work explores the potential for additive manufacturing to be used to fabricate ultraviolet light-blocking or photocatalytic materials with in situ resource utilization, using a titania foam as a model system. Direct foam writing was used to deposit titania-based foam lines in microgravity using parabolic flight. The wet foam was based on titania primary particles and a titania precursor (Ti (IV) bis(ammonium lactato) dihydroxide). Lines were also printed in Earth gravity and their resulting properties were compared with regard to average cross-sectional area, height, and width. The cross-sectional height was found to be higher when printing at low speeds in microgravity compared to Earth gravity, but lower when printing at high speeds in microgravity compared to Earth gravity. It was also observed that volumetric flow rate was generally higher when writing in Earth gravity compared to microgravity. Additionally, heterogeneous photocatalytic degradation of methylene blue was studied to characterize the foams for water purification and was found to generally increase as the foam heat treatment temperature increased. Optical and scanning electron microscopies were used to observe foam morphology. X-ray diffraction spectroscopy was used to study the change in crystallinity with respect to temperature. Contact angle of water was found to increase on the surface of the foam as ultraviolet light exposure time increased. Additionally, the foam blocked more ultraviolet light over time when exposed to ultraviolet radiation. Finally, bubble coarsening measurements were taken to observe bubble radius growth over time.

Schlagwörter

Stichwörter der Autor:innen

Direct foam writingadditive manufacturingmicrogravityphotocatalysistitanium dioxide

Autor:innen und Institutionen

  • Department of Mechanical and Aerospace Engineering, West Virginia University, Morgantown, West Virginia 26506, United States.

ORCID-Profile: G Jacob Cordonier, Konstantinos A Sierros

Förderung

  • Department of Mechanical and Aerospace Engineering, West Virginia University
  • National Aeronautics and Space Administration

Zitieren

APA

Cordonier, G. J., Anderson, K., Butts, R., O'Hara, R., Garneau, R., Wimer, N., Kuhlman, J. M., & Sierros, K. A. (2023). Direct Writing of a Titania Foam in Microgravity for Photocatalytic Applications. ACS Applied Materials & Interfaces, 15(40), 47745-47753. https://doi.org/10.1021/acsami.3c09658

Vancouver

Cordonier GJ, Anderson K, Butts R, O'Hara R, Garneau R, Wimer N, et al. Direct Writing of a Titania Foam in Microgravity for Photocatalytic Applications. ACS Applied Materials & Interfaces. 2023;15(40):47745-47753. doi:10.1021/acsami.3c09658

BibTeX
@article{Cordonier2023,
  author = {Cordonier, G Jacob and Anderson, Kyleigh and Butts, Ronan and O'Hara, Ross and Garneau, Renee and Wimer, Nathanael and Kuhlman, John M and Sierros, Konstantinos A},
  title = {Direct Writing of a Titania Foam in Microgravity for Photocatalytic Applications},
  journal = {ACS Applied Materials & Interfaces},
  year = {2023},
  volume = {15},
  number = {40},
  pages = {47745--47753},
  doi = {10.1021/acsami.3c09658}
}
Kostenlos starten →