EUVIMEDEUVIMED entdecken
Crossref

Influence of Microporous Layers on Interfacial Properties, Oxygen Flow Distribution, and Durability of Proton Exchange Membrane Water Electrolyzers

Devashish Kulkarni, Ryan Ouimet, Bryan Erb, Dilworth Y Parkinson iD, Hung-Ming Chang, Cliffton Wang, Andrew Smeltz, Christopher Capuano, Iryna V Zenyuk iD

ACS Applied Materials & Interfaces · 18.10.2023 · 15 (41) · 48060-48071

DOI: 10.1021/acsami.3c06899 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Materials & Interfaces, online erschienen am 03.10.2023. Verfasst von Devashish Kulkarni und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Material Science and Engineering, University of California Irvine, Irvine, California 92697, United States. Die Arbeit wurde bisher 79-mal zitiert (Crossref) und nennt 29 Literaturangaben. Gefördert von: Basic Energy Sciences, Hydrogen and Fuel Cell Technologies Office.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The efficient and cost-effective production of green hydrogen is essential to decarbonize heavily polluting sectors such as transportation and heavy manufacturing industries such as metal refining. Polymer electrolyte membrane water electrolysis (PEMWE) is the most promising and rapidly maturing technology for producing green hydrogen at a scale and on demand. However, substantial cost reduction by lowering precious metal catalyst loadings and efficiency improvement is necessary to lower the cost of the produced hydrogen. Porous transport layers (PTLs) play a major role in influencing the PEMWE efficiency and catalyst utilization. Several studies have projected that the use of microporous layers (MPLs) on PTLs can improve the efficiency of PEMWEs, but very limited literature exists on how MPLs affect anodic interfacial properties and oxygen transport in PTLs. In this study, for the first time, we use X-ray microtomography and innovative image processing techniques to elucidate the oxygen flow patterns in PTLs with varying MPL thicknesses. We used stained water to improve contrast of oxygen in PTLs and demonstrate visualization of time averaged oxygen flow patterns. The results show that PTLs with MPLs significantly improve interfacial contact by almost 20% as compared to single layer sintered PTL. For the single layer PTL without MPL, the pore volume utilization for oxygen flow is low and the oxygen follows a viscous fingering flow regime. With MPLs, the pore volume utilization is higher, and the number of oxygen transport pathways is increased significantly. MPLs were also shown to suppress capillary fingering and transition oxygen flow to the viscous fingering regime, which has been proven to decrease site masking effects. Finally, durability tests showed the least voltage degradation for thin MPL and thicker MPLs run into mass transport limitations. Based on these findings, PTL/MPL design optimization strategies are proposed for enabling low catalyst loadings and improving durability.

Schlagwörter

Stichwörter der Autor:innen

X-ray computed tomographymicroporous layersoxygen transportpolymer electrolyte membrane water electrolyzersporous transport layers

Autor:innen und Institutionen

  • Department of Material Science and Engineering, University of California Irvine, Irvine, California 92697, United States.
  • Nel Hydrogen, Wallingford, Connecticut 06492, United States.
  • De Nora Tech, LLC, Concord, Ohio 44077, United States.
  • Department of Chemical and Biomolecular Engineering; National Fuel Cell Research Center, University of California Irvine, Irvine, California 92697, United States.
  • Energy Technologies Area, Energy Conversion Group, Lawrence Berkeley National Laboratory, Berkeley, California 94720, United States.

ORCID-Profile: Dilworth Y Parkinson, Iryna V Zenyuk

Förderung

  • Basic Energy Sciences
  • Hydrogen and Fuel Cell Technologies Office

Zitieren

APA

Kulkarni, D., Ouimet, R., Erb, B., Parkinson, D. Y., Chang, H. M., Wang, C., Smeltz, A., Capuano, C., & Zenyuk, I. V. (2023). Influence of Microporous Layers on Interfacial Properties, Oxygen Flow Distribution, and Durability of Proton Exchange Membrane Water Electrolyzers. ACS Applied Materials & Interfaces, 15(41), 48060-48071. https://doi.org/10.1021/acsami.3c06899

Vancouver

Kulkarni D, Ouimet R, Erb B, Parkinson DY, Chang HM, Wang C, et al. Influence of Microporous Layers on Interfacial Properties, Oxygen Flow Distribution, and Durability of Proton Exchange Membrane Water Electrolyzers. ACS Applied Materials & Interfaces. 2023;15(41):48060-48071. doi:10.1021/acsami.3c06899

BibTeX
@article{Kulkarni2023,
  author = {Kulkarni, Devashish and Ouimet, Ryan and Erb, Bryan and Parkinson, Dilworth Y and Chang, Hung-Ming and Wang, Cliffton and Smeltz, Andrew and Capuano, Christopher and Zenyuk, Iryna V},
  title = {Influence of Microporous Layers on Interfacial Properties, Oxygen Flow Distribution, and Durability of Proton Exchange Membrane Water Electrolyzers},
  journal = {ACS Applied Materials & Interfaces},
  year = {2023},
  volume = {15},
  number = {41},
  pages = {48060--48071},
  doi = {10.1021/acsami.3c06899}
}
Kostenlos starten →