EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Freeze-Cast Porous Textured BaTiO 3 –Polymer Composites for Energy Harvesting Applications

Ajeet Kumar iD, Alex Tezcan, Zihe Li iD, Ruxue Yang, Florian Bouville iD, Guylaine Poulin-Vittrant, Hamideh Khanbareh, James Roscow, Sylvain Deville iD, Chris Bowen iD

ACS Applied Energy Materials · 11.08.2025 · 8 (15) · 11437-11446

DOI: 10.1021/acsaem.5c01606 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Energy Materials, online erschienen am 22.07.2025. Verfasst von Ajeet Kumar und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, University of Bath, Bath BA27AY, United Kingdom. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: UK Research and Innovation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Porous piezoelectric ceramics exhibit a unique combination of high piezoelectric charge coefficients (d ij ) and low permittivity compared to their dense counterparts, which is desirable for achieving high piezosensing and energy harvesting performance. A further enhancement in performance can be achieved by inducing crystallographic texturing within the porous lead-free piezoceramic matrix while maintaining the aligned porous structure. Here, we report a process demonstrating the use of directional freeze-casting of BaTiO3 platelets to fabricate lead-free porous textured BaTiO3 ceramics with highly aligned porosity. A high degree of alignment of the piezoelectric BaTiO3 platelets in the freezing direction was confirmed by using scanning electron microscopy. The degree of texturing was quantified by X-ray diffraction, yielding a Lotgering factor (LF) of ∼0.37. To enhance the mechanical strength and strain to failure for sensing and harvesting applications, the porous textured BaTiO3 ceramics (∼60 vol % porosity, sintered at 1150 °C for 4 h) were infiltrated with polymers (epoxy and polydimethylsiloxane) of contrasting elastic properties. The BaTiO3-epoxy composite structure demonstrated a strain (%) to failure of 0.93 ± 0.005 at a high failure stress of 71.6 ± 3.05 MPa, with Young's modulus of 7.6 ± 0.02 GPa. In contrast, the BaTiO3-PDMS composite had a flexible nature and exhibited a lower Young's modulus of 0.015 ± 0.0012 GPa and a higher strain (%) to failure (>22 ± 1.5). The dielectric properties, polarization-electric field loops, and piezoelectric properties were examined in detail, and the poled BaTiO3-epoxy composite was used to fabricate a cantilever structure to demonstrate its energy harvesting and sensing performance. This work has shown that directional freeze-casting can produce an aligned porous and textured ferroelectric microstructure for sensing or energy harvesting applications.

Schlagwörter

Stichwörter der Autor:innen

compositesenergy harvestinglead-freemechanical propertiespiezoelectricporous

Autor:innen und Institutionen

  • Department of Mechanical Engineering, University of Bath, Bath BA27AY, United Kingdom.
  • Centre for Advanced Structural Ceramics, Department of Materials, Imperial College, London SW7 2AZ, United Kingdom.
  • GREMAN UMR 7347, CNRS, University of Tours, INSA-CVL, Blois 41000, France.
  • Universite Claude Bernard Lyon 1, CNRS, Institut Lumière Matière, UMR5306, F-69100 Villeurbanne, France.

ORCID-Profile: Ajeet Kumar, Zihe Li, Florian Bouville, Sylvain Deville, Chris Bowen

Förderung

  • UK Research and Innovation

Zitieren

APA

Kumar, A., Tezcan, A., Li, Z., Yang, R., Bouville, F., Poulin-Vittrant, G., Khanbareh, H., Roscow, J., Deville, S., & Bowen, C. (2025). Freeze-Cast Porous Textured BaTiO 3 –Polymer Composites for Energy Harvesting Applications. ACS Applied Energy Materials, 8(15), 11437-11446. https://doi.org/10.1021/acsaem.5c01606

Vancouver

Kumar A, Tezcan A, Li Z, Yang R, Bouville F, Poulin-Vittrant G, et al. Freeze-Cast Porous Textured BaTiO 3 –Polymer Composites for Energy Harvesting Applications. ACS Applied Energy Materials. 2025;8(15):11437-11446. doi:10.1021/acsaem.5c01606

BibTeX
@article{Kumar2025,
  author = {Kumar, Ajeet and Tezcan, Alex and Li, Zihe and Yang, Ruxue and Bouville, Florian and Poulin-Vittrant, Guylaine and Khanbareh, Hamideh and Roscow, James and Deville, Sylvain and Bowen, Chris},
  title = {Freeze-Cast Porous Textured BaTiO 3 –Polymer Composites for Energy Harvesting Applications},
  journal = {ACS Applied Energy Materials},
  year = {2025},
  volume = {8},
  number = {15},
  pages = {11437--11446},
  doi = {10.1021/acsaem.5c01606}
}
Kostenlos starten →