Flexible, Solution-Processable Electrostatic Discharge Protective Coatings from Upcycled Waste Tire Pyrolysis Char via Sequential Acid-Alkali Leaching
ACS Applied Electronic Materials · 10.11.2026
DOI: 10.1021/acsaelm.6c01491 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Applied Electronic Materials, online erschienen am 10.11.2026. Verfasst von Subash Chandra Bose Rapaka und 9 weiteren Autor:innen. Die Arbeit nennt 38 Literaturangaben. Gefördert von: Ministry of Electronics and Information technology.
Abstract (Originalsprache)
We demonstrate flexible, solution-processable electrostatic discharge (ESD) protective coatings whose conductive filler is derived from upcycled tire pyrolysis char (TPC), a hazardous residue of end-of-life tire pyrolysis. A three-stage protocol uses 6 M HCl, 4 M NaOH, and 6 M HNO3, each at 80 °C for 3 h, for demineralization, desilication, and surface oxidation, respectively. The contribution is integration of established leaching chemistry with purity tracking and device characterization for one carbon stream. Inductively coupled plasma optical emission spectroscopy showed that the sum of quantified elemental concentrations decreased from 4.92 to 0.076 wt %, approximately 98.5%. Ash decreased from 9.85 wt % on an as-received basis (10.9 wt % on a dry basis) to 0.15 wt %, with Zn, Fe, Ca, and Al below the detection limit (≤5 mg kg−1). The quantified elements other than S, expressed as oxides, account for 79% of the dry-basis ash. The purified char (PTPC) showed a lower Raman D/G ratio (0.27 to 0.22), a 38.5% larger Brunauer−Emmett−Teller surface area, and oxygen-containing surface groups. Surface oxidation and improved interparticle contacts are plausible contributors to performance; their individual contributions were not isolated experimentally. Doctor-blade-coated nitrocellulose-bound films on poly(ethylene terephthalate) (PET) gave approximately 1 kΩ sq−1 sheet resistance and dissipated 99% of a 1 kV contact-discharge pulse in approximately 368 μs. The ink was shear-thinning (power-law n = 0.35). After 1000 bending cycles at a 5 mm radius, resistance increased by approximately 8% on PET and 25% on cellulose paper; PET-supported coatings showed approximately 2% drift after 30 days of ambient aging. Preliminary all-in costs are USD 4.3–7.0 kg−1, including reagents at USD 2.1–3.1 kg−1 with acid-liquor reuse. These estimates and proposed Zn and silica recovery remain unvalidated at pilot scale. The protocol demonstrates a laboratory-scale route from waste char to conductive carbon for flexible ESD protection.
Förderung
- Ministry of Electronics and Information technology
Zitieren
APA
Rapaka, S. C. B., Lakavath, P. N., Naik, C. A., Machinao, S., Bhukya, M., Chintha, S., Kadari, R., Nasani, N., Urlagaddala, R., & Karuppannan, R. (2026). Flexible, Solution-Processable Electrostatic Discharge Protective Coatings from Upcycled Waste Tire Pyrolysis Char via Sequential Acid-Alkali Leaching. ACS Applied Electronic Materials. https://doi.org/10.1021/acsaelm.6c01491
Vancouver
Rapaka SCB, Lakavath PN, Naik CA, Machinao S, Bhukya M, Chintha S, et al. Flexible, Solution-Processable Electrostatic Discharge Protective Coatings from Upcycled Waste Tire Pyrolysis Char via Sequential Acid-Alkali Leaching. ACS Applied Electronic Materials. 2026. doi:10.1021/acsaelm.6c01491
BibTeX
@article{Rapaka2026,
author = {Rapaka, Subash Chandra Bose and Lakavath, Prashanth Naik and Naik, Chavan Akash and Machinao, Sochannao and Bhukya, Mahender and Chintha, Sudheer and Kadari, Ramaswamy and Nasani, Narendar and Urlagaddala, Rambabu and Karuppannan, Ramesh},
title = {Flexible, Solution-Processable Electrostatic Discharge Protective Coatings from Upcycled Waste Tire Pyrolysis Char via Sequential Acid-Alkali Leaching},
journal = {ACS Applied Electronic Materials},
year = {2026},
doi = {10.1021/acsaelm.6c01491}
}
EUVIMED