Manufacturing Route-Dependent Biointerface Modulation in 3D-Printed and Conventional Dental Implant Systems
ACS Applied Bio Materials · 02.11.2026 · 9 (21) · 10090-10106
DOI: 10.1021/acsabm.6c00473 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Applied Bio Materials, online erschienen am 12.10.2026. Verfasst von Maria Helena Rossy Borges und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics and Periodontology, Piracicaba Dental School, Universidade Estadual de Campinas (UNICAMP), Piracicaba, São Paulo13414-90…. Hauptthemen laut MEDLINE: Dental Implants, Printing, Three-Dimensional, Biocompatible Materials. Die Arbeit nennt 59 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Fundação de Amparo à Pesquisa do Estado de São Paulo, Coordenação de Aperfeiçoamento de Pessoal de Nível Superior, Conselho Nacional de Desenvolvimento Científico e Tecnológico.
Abstract (Originalsprache)
Implant manufacturing routes determine surface architecture and, consequently, modulate biointerface interactions that govern early biological responses. Although additive manufacturing has emerged as a promising alternative to conventional subtractive techniques, direct comparisons among commercially available systems remain limited. In this study, a commercially available additively manufactured dental implant was compared with four market-available conventionally machined systems to elucidate manufacturing route-dependent biointerface modulation. Physicochemical properties, surface topography, and electrochemical behavior were evaluated alongside biological responses. Protein adsorption profiles were characterized by liquid chromatography–tandem mass spectrometry (LC–MS/MS), while polymicrobial accumulation was quantified and profiled. Microbially induced surface degradation was assessed by titanium ion release. The additively manufactured implant and the market-leading conventional system exhibited higher surface roughness and distinctive topographical features, which were associated with reduced polymicrobial biofilm accumulation, lower titanium ion release following microbial challenge, and stable electrochemical behavior. Although conventionally machined implants exhibited broader proteomic profiles, functional enrichment analyses revealed overlapping biological categories among implant systems. Collectively, the findings demonstrate that the manufacturing route critically modulates implant biointerface characteristics, with additive manufacturing achieving performance comparable to established commercial systems.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Prosthodontics and Periodontology, Piracicaba Dental School, Universidade Estadual de Campinas (UNICAMP), Piracicaba, São Paulo13414-903, Brazil.
- Dental Research Division, Universidade Universus Veritas Guarulhos, Guarulhos07023-070, Brazil.
- Faculdade Israelita de Ciências da Saúde Albert Einstein, Hospital Israelita Albert Einstein, São Paulo05653-000, Brazil.
- Dental Science School (Faculdade de Ciências Odontológicas) , Montes Claros39401-303, Brazil.
- Dental School, State University of Montes Claros, Montes Claros39401-832, Brazil.
- Department of Oral Health Sciences, Periodontology and Oral Microbiology, KU Leuven, Leuven3000, Belgium.
ORCID-Profile: Valentim A R Barão, João Gabriel S Souza
Förderung
- Fundação de Amparo à Pesquisa do Estado de São Paulo
- Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
- Conselho Nacional de Desenvolvimento Científico e Tecnológico
- Conselho Nacional de Desenvolvimento Cient?fico e Tecnol?gico
- Funda??o de Amparo ? Pesquisa do Estado de S?o Paulo
- Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior
Zitieren
APA
Borges, M. H. R., Marques, M. D. C., Souza, J. N., Ribeiro, L. R. M., de Andrade, C. S. A. F., de Souza Junior, A. R., Vechiato-Filho, A. J., Barão, V. A. R., Shibli, J. A., & Souza, J. G. S. (2026). Manufacturing Route-Dependent Biointerface Modulation in 3D-Printed and Conventional Dental Implant Systems. ACS Applied Bio Materials, 9(21), 10090-10106. https://doi.org/10.1021/acsabm.6c00473
Vancouver
Borges MHR, Marques MDC, Souza JN, Ribeiro LRM, de Andrade CSAF, de Souza Junior AR, et al. Manufacturing Route-Dependent Biointerface Modulation in 3D-Printed and Conventional Dental Implant Systems. ACS Applied Bio Materials. 2026;9(21):10090-10106. doi:10.1021/acsabm.6c00473
BibTeX
@article{Borges2026,
author = {Borges, Maria Helena Rossy and Marques, Marcio da Costa and Souza, Julia Nascimento and Ribeiro, Luis Rafael Mangueira and de Andrade, Catia Sufia Alves Freire and de Souza Junior, Agnaldo R and Vechiato-Filho, Aljomar José and Barão, Valentim A R and Shibli, Jamil A and Souza, João Gabriel S},
title = {Manufacturing Route-Dependent Biointerface Modulation in 3D-Printed and Conventional Dental Implant Systems},
journal = {ACS Applied Bio Materials},
year = {2026},
volume = {9},
number = {21},
pages = {10090--10106},
doi = {10.1021/acsabm.6c00473}
}
EUVIMED