EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Graphene and Ti 3 C 2 T x MXene Nanomaterial-Infused Bioinks for Mechanical and Electrical Improvement of 3D Bioprinted Scaffolds

Miranda Lea Nelson, Hailey Burgoyne, Fereshteh Rajabi Kouchi, Felix White, Attila Rektor, Kiyo Fujimoto, Mone't Sawyer, Annaka Tibbits, Elham Hosseini Toodeshki, Amevi M Semodji, Trevor J Lujan, Tony Valayil Varghese iD und 3 weitere

ACS Applied Bio Materials · 19.01.2026 · 9 (2) · 1142-1155

DOI: 10.1021/acsabm.5c02206 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Bio Materials, online erschienen am 06.01.2026. Verfasst von Miranda Lea Nelson und 14 weiteren Autor:innen. Beteiligte Einrichtung: Biomedical Engineering Doctoral Program, Boise State University, Boise, Idaho 83725, United States. Hauptthemen laut MEDLINE: Graphite, Tissue Scaffolds, Titanium, Printing, Three-Dimensional. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 117 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: NCRR NIH HHS, NIGMS NIH HHS, Idaho State Board of Education.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The precise control of bioink formulation, process parameters, and scaffold geometries has enabled some critical limitations of bioprinting to be overcome and has transformed the construction of functional 3-dimensional (3D) bioscaffolds for tissue engineering (TE). Current bioscaffolds fall short in producing functional tissue due to a lack of the physiological, mechanical, and electrical environments necessary for optimal cell development. In this study, we report the incorporation of the nanomaterial (NM) graphene/graphene oxide (GGO) and titanium carbide (Ti3C2Tx MXene) into an alginate-cellulose-based bioink to enhance printability and modify the physical properties of bioprinted scaffolds to better mimic physiological conditions. Our results indicate that incorporating Ti3C2Tx MXene nanoflakes into the alginate cellulose-based bioink from CELLINK improved the compressive Young's modulus by approximately 72% and enhanced the electrical conductivity by 0.39 S/m. The inclusion of GGO improved conductivity by 0.12 S/m but did not improve the compressive Young's modulus. Biocompatibility of the CELLINK bioink enhanced with NMs was demonstrated in mouse myoblast cells (C2C12), followed by live/dead confocal imaging, which showed greater than 95% viability for each ink. Our results suggest these electrically conductive NMs can be used to tune the physical properties of bioinks for 3D-bioprinted scaffolds specific to cell types and stimuli.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

GraphiteTissue ScaffoldsTitaniumPrinting, Three-DimensionalNanostructuresBioprintingBiocompatible MaterialsAnimalsInkMaterials TestingMiceElectric ConductivityParticle SizeTissue EngineeringSurface PropertiesAlginatesNitritesTransition Elements

Stichwörter der Autor:innen

Ti3C2Tx MXenebioinkbioprintinggraphenegraphene oxidenanomaterialtissue engineering

Substanzen

Graphitetitanium carbideTitaniumBiocompatible MaterialsAlginatesMXeneNitritesTransition Elements

Autor:innen und Institutionen

  • Biomedical Engineering Doctoral Program, Boise State University, Boise, Idaho 83725, United States.
  • Micron School for Materials Science and Engineering, Boise State University, Boise, Idaho 83725, United States.
  • Electrical and Computer Engineering, Boise State University, Boise, Idaho 83725, United States.
  • Idaho National Laboratory, Idaho Falls, Idaho 83401, United States.
  • Department of Mechanical & Biomedical Engineering, Boise State University, Boise, Idaho 83725, United States.
  • Department of Physics, Boise State University, Boise, Idaho 83725, United States.

ORCID-Profile: Tony Valayil Varghese, Josh Eixenberger, David Estrada

Förderung

  • NCRR NIH HHS
  • NIGMS NIH HHS
  • Idaho State Board of Education
  • M.J. Murdock Charitable Trust
  • National Center for Medical Rehabilitation Research
  • Boise State University
  • National Institute of General Medical Sciences
  • National Science Foundation

Zitieren

APA

Nelson, M. L., Burgoyne, H., Kouchi, F. R., White, F., Rektor, A., Fujimoto, K., Sawyer, M., Tibbits, A., Toodeshki, E. H., Semodji, A. M., Lujan, T. J., Varghese, T. V., Eixenberger, J., Montenegro-Brown, R., & Estrada, D. (2026). Graphene and Ti 3 C 2 T x MXene Nanomaterial-Infused Bioinks for Mechanical and Electrical Improvement of 3D Bioprinted Scaffolds. ACS Applied Bio Materials, 9(2), 1142-1155. https://doi.org/10.1021/acsabm.5c02206

Vancouver

Nelson ML, Burgoyne H, Kouchi FR, White F, Rektor A, Fujimoto K, et al. Graphene and Ti 3 C 2 T x MXene Nanomaterial-Infused Bioinks for Mechanical and Electrical Improvement of 3D Bioprinted Scaffolds. ACS Applied Bio Materials. 2026;9(2):1142-1155. doi:10.1021/acsabm.5c02206

BibTeX
@article{Nelson2026,
  author = {Nelson, Miranda Lea and Burgoyne, Hailey and Kouchi, Fereshteh Rajabi and White, Felix and Rektor, Attila and Fujimoto, Kiyo and Sawyer, Mone't and Tibbits, Annaka and Toodeshki, Elham Hosseini and Semodji, Amevi M and Lujan, Trevor J and Varghese, Tony Valayil and Eixenberger, Josh and Montenegro-Brown, Raquel and Estrada, David},
  title = {Graphene and Ti 3 C 2 T x MXene Nanomaterial-Infused Bioinks for Mechanical and Electrical Improvement of 3D Bioprinted Scaffolds},
  journal = {ACS Applied Bio Materials},
  year = {2026},
  volume = {9},
  number = {2},
  pages = {1142--1155},
  doi = {10.1021/acsabm.5c02206}
}
Kostenlos starten →