EUVIMEDEUVIMED entdecken
Crossref

Injectable and 3D Extrusion Printable Hydrophilic Silicone-Based Hydrogels for Controlled Ocular Delivery of Ophthalmic Drugs

Sayan Ganguly iD, David Wulff, Chau-Minh Phan, Lyndon William Jones, Xiaowu Shirley Tang iD

ACS Applied Bio Materials · 16.09.2024 · 7 (9) · 6286-6296

DOI: 10.1021/acsabm.4c00901 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ACS Applied Bio Materials, online erschienen am 03.09.2024. Verfasst von Sayan Ganguly und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry, University of Waterloo, 200 University Ave West, Waterloo, Ontario N2L 3G1, Canada. Hauptthemen laut MEDLINE: Hydrogels, Printing, Three-Dimensional, Biocompatible Materials, Materials Testing. Die Arbeit wurde bisher 61-mal zitiert (Crossref) und nennt 56 Literaturangaben. Gefördert von: Hong Kong Special Administrative Region Government, InnoHK initiative.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

While silicone elastomers have found widespread use in the biomedical industry, 3D printing them has proven to be difficult due to the material's slow drying time, low viscosity, and hydrophobicity. Herein, we arrested the hydrophilic silicone (HS) macrochains into a semi-interpenetrating polymer network (semi-IPN) via an in situ photogelation-assisted 3D microextrusion printing technique. The flow behavior of the pregel solutions and the mechanical properties of the printed HS hydrogels were tested, showing a high elastic modulus (approximately 15 kPa), a low tan δ, high elasticity, and delayed network rupturing. The uniaxial compression tests demonstrated a nearly negligible permanent deformation, suggesting that the printed hybrid hydrogel maintained its elastic properties. Drug loading and diffusion in the microporous hydrogel are shown via the non-Fickian anomalous transport mechanism, leading to highly tunable loading/releasing profiles (approximately 20% cumulative release) depending on the HS concentration. The drug encapsulation exhibits exceptional stability, remaining intact without any degradation even after a storage period of 1 month. As far as we know, this is the first soft biomaterial based on HS that functions as an exceptional controlled drug delivery device.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

HydrogelsPrinting, Three-DimensionalBiocompatible MaterialsMaterials TestingHydrophobic and Hydrophilic InteractionsSiliconesDrug Delivery SystemsParticle SizeOphthalmic Solutions

Stichwörter der Autor:innen

3D microextrusiondrug deliveryhybrid hydrogelhydrophilic siliconesoft biomaterial

Substanzen

HydrogelsBiocompatible MaterialsSiliconesOphthalmic Solutions

Autor:innen und Institutionen

  • Department of Chemistry, University of Waterloo, 200 University Ave West, Waterloo, Ontario N2L 3G1, Canada.
  • Centre for Eye and Vision Research Limited, 17W, Hong Kong Science Park, Hong Kong.
  • School of Optometry and Vision Science, Faculty of Science, University of Waterloo, Waterloo, Ontario N2L 3G1, Canada.

ORCID-Profile: Sayan Ganguly, Xiaowu Shirley Tang

Förderung

  • Hong Kong Special Administrative Region Government
  • InnoHK initiative

Zitieren

APA

Ganguly, S., Wulff, D., Phan, C. M., Jones, L. W., & Tang, X. S. (2024). Injectable and 3D Extrusion Printable Hydrophilic Silicone-Based Hydrogels for Controlled Ocular Delivery of Ophthalmic Drugs. ACS Applied Bio Materials, 7(9), 6286-6296. https://doi.org/10.1021/acsabm.4c00901

Vancouver

Ganguly S, Wulff D, Phan CM, Jones LW, Tang XS. Injectable and 3D Extrusion Printable Hydrophilic Silicone-Based Hydrogels for Controlled Ocular Delivery of Ophthalmic Drugs. ACS Applied Bio Materials. 2024;7(9):6286-6296. doi:10.1021/acsabm.4c00901

BibTeX
@article{Ganguly2024,
  author = {Ganguly, Sayan and Wulff, David and Phan, Chau-Minh and Jones, Lyndon William and Tang, Xiaowu Shirley},
  title = {Injectable and 3D Extrusion Printable Hydrophilic Silicone-Based Hydrogels for Controlled Ocular Delivery of Ophthalmic Drugs},
  journal = {ACS Applied Bio Materials},
  year = {2024},
  volume = {7},
  number = {9},
  pages = {6286--6296},
  doi = {10.1021/acsabm.4c00901}
}
Kostenlos starten →