EUVIMEDEUVIMED entdecken
Crossref

One-Pot, Dual-Wavelength 3D Printing of Bottlebrush-Based Multimaterials

Justin J. Yun, Nadia Chapple, Divya J. Iyer, Andrew Rhode, Juan Manuel Urueña, Craig J. Hawker, Christopher M. Bates

Macromolecules · 10.11.2026 · 59 (21) · 11913-11922

DOI: 10.1021/acs.macromol.6c02209 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Macromolecules, online erschienen am 23.10.2026. Verfasst von Justin J. Yun und 6 weiteren Autor:innen. Die Arbeit nennt 39 Literaturangaben. Gefördert von: Army Research Office, U.S. Department of Education, National Science Foundation (NSF).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Multimaterial 3D printing requires resin platforms that independently control softness, stiffness, and interfacial integrity within a single printed object. Here we demonstrate that crosslinkable bottlebrush polymers provide a versatile architecture for dual-wavelength printing of elastomers with mechanical contrast. UV irradiation (365 nm) efficiently crosslinks pendant 1,2-dithiolanes attached to the ends of polyethylene glycol side chains to form supersoft, dynamic bottlebrush networks with a tunable tensile modulus from 2 to 200 kPa by varying the lipoate content or acrylate comonomer concentration. Incorporation of an acrylate–epoxy hybrid monomer enables a second, orthogonal curing step: blue-light irradiation (460 nm) activates cationic epoxide polymerization to install a reinforcing network and increase the modulus into the MPa range, with post-cured materials reaching up to 200 MPa. This sequential radical/cationic strategy produces stiff–soft multimaterials from a single resin with high gel fractions, robust interfaces, and diffuse fracture behavior. Importantly, dual-cured networks have a higher stiffness than those obtained by curing acrylate-free resins, demonstrating that crosslinker chemistry controls network topology and mechanical properties. Together, these results establish lipoate-functional bottlebrush polymers as a modular platform for single-resin multimaterial 3D printing, where polymer architecture and temporally controlled photochemistry combine to program kPa-to-MPa mechanical contrast, degradability, and interfacial toughness.

Förderung

  • Army Research Office
  • U.S. Department of Education
  • National Science Foundation (NSF)

Zitieren

APA

Yun, J. J., Chapple, N., Iyer, D. J., Rhode, A., Urueña, J. M., Hawker, C. J., & Bates, C. M. (2026). One-Pot, Dual-Wavelength 3D Printing of Bottlebrush-Based Multimaterials. Macromolecules, 59(21), 11913-11922. https://doi.org/10.1021/acs.macromol.6c02209

Vancouver

Yun JJ, Chapple N, Iyer DJ, Rhode A, Urueña JM, Hawker CJ, et al. One-Pot, Dual-Wavelength 3D Printing of Bottlebrush-Based Multimaterials. Macromolecules. 2026;59(21):11913-11922. doi:10.1021/acs.macromol.6c02209

BibTeX
@article{Yun2026,
  author = {Yun, Justin J. and Chapple, Nadia and Iyer, Divya J. and Rhode, Andrew and Urueña, Juan Manuel and Hawker, Craig J. and Bates, Christopher M.},
  title = {One-Pot, Dual-Wavelength 3D Printing of Bottlebrush-Based Multimaterials},
  journal = {Macromolecules},
  year = {2026},
  volume = {59},
  number = {21},
  pages = {11913--11922},
  doi = {10.1021/acs.macromol.6c02209}
}
Kostenlos starten →