A Precise Pore-Structure Matching Method for Microfluidic Chips and Core Porous Media and Its Oil-Displacement Mechanisms
Langmuir · 11.08.2026 · 42 (31) · 22758-22774
DOI: 10.1021/acs.langmuir.6c02500 ↗Kurz gefasst
Fachartikel in der Zeitschrift Langmuir, online erschienen am 27.07.2026. Verfasst von Ruibo Cao und 8 weiteren Autor:innen. Beteiligte Einrichtung: Key Laboratory for Enhanced Oil & Gas Recovery of the Ministry of Education, Northeast Petroleum University, Daqing163318, Heilongjiang, China. Die Arbeit nennt 60 Literaturangaben.
Abstract (Originalsprache)
Microfluidic chips are widely used to investigate pore-scale oil-displacement mechanisms, but the quantitative matching between chip pore structures and real reservoir cores remains insufficient. In this study, a quantitative pore-structure matching workflow was developed by integrating image processing, vector conversion, a self-developed MATLAB-based two-dimensional (2D) image editor, pore-structure characterization, microfluidic visualization experiments, and numerical simulation. Key parameters, including porosity, permeability, pore-throat radius, pore-throat ratio, and coordination number, were used to evaluate the matching between microfluidic chips and reservoir cores. The results show that the proposed method enabled pixel-level editing and synchronous regulation of pore-throat structures. Three chip models, including homogeneous high-permeability, homogeneous low-permeability, and heterogeneous models, were constructed, with a controllable permeability range of 200–1000 mD. By combining image analysis, core fluorescence analysis, constant-rate mercury intrusion, and COMSOL simulation, the matching degree between the chip models and real core pore-structure parameters exceeded 90%, indicating that the chips effectively reproduced the main pore-throat characteristics of the target reservoir. Visualization oil-displacement experiments further demonstrated that 15–30 μm preformed particle gel (PPG) particles achieved effective pore-throat matching through selective plugging, flow diversion, and deep profile control. The adaptive plugging, profile-control, and displacement system significantly improved sweep efficiency in the heterogeneous model, with recovery factors of 95.03% and 85.7% in the high- and low-permeability layers, respectively, higher than those obtained by weak-alkali ASP flooding. Numerical simulations identified the optimal displacement parameters as a viscosity of 70 mPa·s and an interfacial tension of 0.03 mN/m. This study provides a quantitative method for designing representative microfluidic chips and offers experimental and numerical support for pore-scale EOR mechanism analysis.
Autor:innen und Institutionen
- Key Laboratory for Enhanced Oil & Gas Recovery of the Ministry of Education, Northeast Petroleum University, Daqing163318, Heilongjiang, China.
- Exploration and Development Research Institute of Daqing Oilfield Limited Company, Daqing163712, Heilongjiang, China.
- Project Management Department for Enhanced Oil Recovery, Daqing Oilfield Co., Ltd., Daqing163453, Heilongjiang, China.
ORCID-Profile: Lihui Wang
Zitieren
APA
Cao, R., Wang, L., Zhang, X., Yan, W., Ren, X., Pi, Y., Xu, T., Wang, Y., & Ning, Y. (2026). A Precise Pore-Structure Matching Method for Microfluidic Chips and Core Porous Media and Its Oil-Displacement Mechanisms. Langmuir, 42(31), 22758-22774. https://doi.org/10.1021/acs.langmuir.6c02500
Vancouver
Cao R, Wang L, Zhang X, Yan W, Ren X, Pi Y, et al. A Precise Pore-Structure Matching Method for Microfluidic Chips and Core Porous Media and Its Oil-Displacement Mechanisms. Langmuir. 2026;42(31):22758-22774. doi:10.1021/acs.langmuir.6c02500
BibTeX
@article{Cao2026,
author = {Cao, Ruibo and Wang, Lihui and Zhang, Xiaoqin and Yan, Wei and Ren, Xidong and Pi, Yanfu and Xu, Tianhan and Wang, Yuan and Ning, Yanxi},
title = {A Precise Pore-Structure Matching Method for Microfluidic Chips and Core Porous Media and Its Oil-Displacement Mechanisms},
journal = {Langmuir},
year = {2026},
volume = {42},
number = {31},
pages = {22758--22774},
doi = {10.1021/acs.langmuir.6c02500}
}
EUVIMED