EUVIMEDEUVIMED entdecken
Crossref

The Enhanced Hydrophobic, Photothermal, and Anti-Icing/Ice-Melting Performance of C/TiN/WC/PDMS Composite Coating by Inserting a Thermal Insulation Layer

Lihua Jiang, Lulu Dong iD, Xin Zhou, Kai Tu, Yutong Chen, Xinyi Li, Ting Xiao iD, Xinyu Tan

Langmuir · 26.11.2024 · 40 (47) · 25207-25219

DOI: 10.1021/acs.langmuir.4c03531 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Langmuir, online erschienen am 11.11.2024. Verfasst von Lihua Jiang und 7 weiteren Autor:innen. Beteiligte Einrichtung: College of Materials and Chemical Engineering, Solar Energy High Value Utilization and Green Conversion Hubei Provincial Engineering Research Center,…. Die Arbeit wurde bisher 23-mal zitiert (Crossref) und nennt 46 Literaturangaben. Gefördert von: Natural Science Foundation of Hubei Province.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Enhancing the hydrophobic and photothermal characteristics of the coating can significantly boost its anti-icing/ice-melting capabilities. In this study, an epoxy resin thermal insulation layer is interposed between the aluminum sheet substrate and the C/TiN/WC/PDMS photothermal composite coating. This method not only equips the coating with exceptional superhydrophobic properties but also markedly elevates its photothermal and anti-icing/ice-melting performance. The incorporation of the thermal insulation layer has been observed to elevate the water contact angle from approximately 125° to 155° ± 0.5° while simultaneously reducing the water sliding angle from over 90° to about 4° ± 0.5°. In an environmental setting of -15 °C and 65% ± 5% humidity, under irradiation of 1.0, 0.7, 0.5, and 0.3 kW/m2, the coating with the thermal insulation layer exhibited saturation temperature increments of roughly 4.7, 3.4, 5.4, and 4.6 °C, respectively, compared to the photothermal coating without the insulation layer. In the absence of irradiation, the coating with the insulation layer delayed the freezing time of 80 μL water droplets by up to three and six times compared to the coating without an insulation layer and the bare aluminum sheet substrate, respectively. Furthermore, under 0.3 kW/m2 irradiation, the coating with the insulation layer reduced the initial melting time and complete melting time of ice beads by nearly half and one-third, respectively, whereas the ice beads on the aluminum sheet substrate remained unmelted throughout the observation period.

Autor:innen und Institutionen

  • College of Materials and Chemical Engineering, Solar Energy High Value Utilization and Green Conversion Hubei Provincial Engineering Research Center, Yichang, Hubei 443002, China.
  • College of Electrical Engineering & New Energy, Hubei Provincial Engineering Technology Research Center for Microgrid, China Three Gorges University, Yichang, Hubei 443002, China.

ORCID-Profile: Lulu Dong, Ting Xiao

Förderung

  • Natural Science Foundation of Hubei Province

Zitieren

APA

Jiang, L., Dong, L., Zhou, X., Tu, K., Chen, Y., Li, X., Xiao, T., & Tan, X. (2024). The Enhanced Hydrophobic, Photothermal, and Anti-Icing/Ice-Melting Performance of C/TiN/WC/PDMS Composite Coating by Inserting a Thermal Insulation Layer. Langmuir, 40(47), 25207-25219. https://doi.org/10.1021/acs.langmuir.4c03531

Vancouver

Jiang L, Dong L, Zhou X, Tu K, Chen Y, Li X, et al. The Enhanced Hydrophobic, Photothermal, and Anti-Icing/Ice-Melting Performance of C/TiN/WC/PDMS Composite Coating by Inserting a Thermal Insulation Layer. Langmuir. 2024;40(47):25207-25219. doi:10.1021/acs.langmuir.4c03531

BibTeX
@article{Jiang2024,
  author = {Jiang, Lihua and Dong, Lulu and Zhou, Xin and Tu, Kai and Chen, Yutong and Li, Xinyi and Xiao, Ting and Tan, Xinyu},
  title = {The Enhanced Hydrophobic, Photothermal, and Anti-Icing/Ice-Melting Performance of C/TiN/WC/PDMS Composite Coating by Inserting a Thermal Insulation Layer},
  journal = {Langmuir},
  year = {2024},
  volume = {40},
  number = {47},
  pages = {25207--25219},
  doi = {10.1021/acs.langmuir.4c03531}
}
Kostenlos starten →