Strength, Stiffness, and Poisson’s Ratio Measurements for Cements Used in the Well Completions for the Extended-Duration Gas Production Test on the Alaskan North Slope
Energy & Fuels · 24.09.2026 · 40 (38) · 21200-21212
DOI: 10.1021/acs.energyfuels.5c04832 ↗Kurz gefasst
Fachartikel in der Zeitschrift Energy & Fuels, online erschienen am 10.09.2026. Verfasst von Adrian V. Garcia und 4 weiteren Autor:innen. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Energy Technology Laboratory, U.S. Geological Survey, Energy Resources Program.
Abstract (Originalsprache)
As part of an extended-duration production test from a natural gas hydrate reservoir on the Alaska North Slope, a suite of optical-fiber sensors was encased in the completion cement to provide stable downhole monitoring around each of the four project wells. How the sensors respond to changes in the reservoir over time depends in part on properties of the LiteCRETE, ArcticCem, or Tuned Light cement in which each sensor is encased, and on how well the cement bonded to the well casing, sensors, and sediment formation. Here, we report on physical properties of the cements (compressive and tensile strength, stiffness, and Poisson’s ratio), on the downhole distribution of the cements used in each well, and on the cement bond quality. Physical property measurements are presented for cements sampled during the completion activities for the three wells completed in 2022–2023. Samples were cured while being submerged in water at 2–4 °C, then tested at intervals from ∼30 days to more than one year. After an initial period of rapid increase, cement strengths largely stabilized around 120 days in all cases, meaning that cements in all wells reached their nominal strength plateau four months or more before the production test began. Calculations based on recorded volumes of pumped cement show the subpermafrost, main hole portion of each well is encased only in the higher-density “tail” cement used in that well. Downhole cement evaluation logs from two wells demonstrate how the presence of sensors and other hardware outside the casing interferes with the cement evaluation assessment. Nonetheless, the cement evaluations indicate a generally good bond with the formation and sensors over the gas hydrate reservoir intervals.
Förderung
- National Energy Technology Laboratory
- U.S. Geological Survey
- Energy Resources Program
Zitieren
APA
Garcia, A. V., Waite, W. F., Yoneda, J., Kirksey, J., & Collett, T. S. (2026). Strength, Stiffness, and Poisson’s Ratio Measurements for Cements Used in the Well Completions for the Extended-Duration Gas Production Test on the Alaskan North Slope. Energy & Fuels, 40(38), 21200-21212. https://doi.org/10.1021/acs.energyfuels.5c04832
Vancouver
Garcia AV, Waite WF, Yoneda J, Kirksey J, Collett TS. Strength, Stiffness, and Poisson’s Ratio Measurements for Cements Used in the Well Completions for the Extended-Duration Gas Production Test on the Alaskan North Slope. Energy & Fuels. 2026;40(38):21200-21212. doi:10.1021/acs.energyfuels.5c04832
BibTeX
@article{Garcia2026,
author = {Garcia, Adrian V. and Waite, William F. and Yoneda, Jun and Kirksey, Jim and Collett, Timothy S.},
title = {Strength, Stiffness, and Poisson’s Ratio Measurements for Cements Used in the Well Completions for the Extended-Duration Gas Production Test on the Alaskan North Slope},
journal = {Energy & Fuels},
year = {2026},
volume = {40},
number = {38},
pages = {21200--21212},
doi = {10.1021/acs.energyfuels.5c04832}
}
EUVIMED