EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

3D Printing Filament Composition, Emissions, and Induced Proinflammatory Responses

Jonathan M Beard, Charli S Worth, Dinny Stevens iD, Amanda K Charlton-Sevcik, John Hadynski, Joseph H Taube, Souhail R Al-Abed iD, Christie M Sayes iD

Chemical Research in Toxicology · 17.08.2026 · 39 (8) · 1546-1558

DOI: 10.1021/acs.chemrestox.6c00128 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Chemical Research in Toxicology, online erschienen am 15.07.2026. Verfasst von Jonathan M Beard und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Environmental Science, Baylor University, Waco, Texas76798-7266, United States. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Inflammation. Die Arbeit nennt 89 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Baylor University, U.S. Consumer Product Safety Commission, Center for Environmental Solutions and Emergency Response, U.S. Environmental Protection Agency.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study addresses current gaps in the 3D printing literature for filament composition (polymer type, color, and brand), aerosol emissions, and human health risks. Six metals (aluminum, magnesium, manganese, chromium, iron, and copper) were found in nonmetal filaments depending on polymer type, color, and brand using inductively coupled plasma-mass spectrometry. For copper- and steel-filled filaments, scanning electron microscopy and elemental analysis indicated a higher metal concentration within the filaments than on the surface. More VOCs were emitted from acrylonitrile butadiene styrene (ABS) filaments compared to polylactic acid (PLA) filaments, according to thermal desorption unit samples analyzed by gas chromatography. Styrene, emitted from ABS filaments, appears to pose the greatest potential health risk among known VOCs, given its concentration and reported effects. Toluene and benzaldehyde were emitted in lower concentrations from both ABS and PLA filaments and may pose a potential risk to human health. Based on three inflammatory markers across two exposure times using BEAS-2B epithelial lung cells, steel showed the highest proinflammatory response, possibly due to chromium and overall particulate matter. 3D printer users should minimize aerosolized emissions by taking proper precautions, such as ensuring adequate ventilation and wearing face masks, particularly during extended exposure.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalInflammationHumansVolatile Organic CompoundsCell LineMetalsPolyestersPolymers

Substanzen

Volatile Organic Compoundspoly(lactide)MetalsPolyestersPolymers

Autor:innen und Institutionen

  • Department of Environmental Science, Baylor University, Waco, Texas76798-7266, United States.
  • Department of Biology, Baylor University, Waco, Texas76798-7266, United States.
  • Oak Ridge Institute for Science and Education (ORISE), United States Environmental Protection Agency, Cincinnati, Ohio45268, United States.
  • U.S. Environmental Protection Agency, Office of Applied Science and Environmental Solutions, 26 W. Martin Luther King Dr., Cincinnati, Ohio45268, United States.

ORCID-Profile: Dinny Stevens, Souhail R Al-Abed, Christie M Sayes

Förderung

  • Baylor University
  • U.S. Consumer Product Safety Commission
  • Center for Environmental Solutions and Emergency Response, U.S. Environmental Protection Agency

Zitieren

APA

Beard, J. M., Worth, C. S., Stevens, D., Charlton-Sevcik, A. K., Hadynski, J., Taube, J. H., Al-Abed, S. R., & Sayes, C. M. (2026). 3D Printing Filament Composition, Emissions, and Induced Proinflammatory Responses. Chemical Research in Toxicology, 39(8), 1546-1558. https://doi.org/10.1021/acs.chemrestox.6c00128

Vancouver

Beard JM, Worth CS, Stevens D, Charlton-Sevcik AK, Hadynski J, Taube JH, et al. 3D Printing Filament Composition, Emissions, and Induced Proinflammatory Responses. Chemical Research in Toxicology. 2026;39(8):1546-1558. doi:10.1021/acs.chemrestox.6c00128

BibTeX
@article{Beard2026,
  author = {Beard, Jonathan M and Worth, Charli S and Stevens, Dinny and Charlton-Sevcik, Amanda K and Hadynski, John and Taube, Joseph H and Al-Abed, Souhail R and Sayes, Christie M},
  title = {3D Printing Filament Composition, Emissions, and Induced Proinflammatory Responses},
  journal = {Chemical Research in Toxicology},
  year = {2026},
  volume = {39},
  number = {8},
  pages = {1546--1558},
  doi = {10.1021/acs.chemrestox.6c00128}
}
Kostenlos starten →