Characterization of Emissions from Carbon Dioxide Laser Cutting Acrylic Plastics
ACS Chemical Health & Safety · 24.07.2023 · 30 (4) · 182-192
DOI: 10.1021/acs.chas.3c00013 ↗Kurz gefasst
Fachartikel in der Zeitschrift ACS Chemical Health & Safety, online erschienen am 22.06.2023. Verfasst von Alejandro Munoz und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Environmental Health Sciences, Fielding School of Public Health, University of California-Los Angeles, Los Angeles, California 90095-17…. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: NIEHS NIH HHS, National Institute of Environmental Health Sciences, University of California, Los Angeles.
Abstract (Originalsprache)
Carbon dioxide laser cutters are used to cut and engrave on various types of materials, including metals, wood, and plastics. Although many are equipped with fume extractors for removing airborne substances generated during laser cutting, gases and particulate matter can be released upon opening the lid after completion. This study focused on investigating laser cutting acrylic sheets and associated emissions. Real-time instruments were utilized to monitor both particulate concentrations and size distributions, while the patented Tsai diffusion sampler was used to collect particulate samples on a polycarbonate membrane and transmission electron microscopy (TEM) grid. Identification of released gases consisted of the use of gas sampling with Teflon gas bags followed by analysis using gas chromatography-mass spectrometry (GC-MS). A portable ambient infrared air analyzer was used to quantify the concentrations of the chemicals released by laser cutting activities. The results of the study found that a significant concentration of particulate matter, including nanoplastic particles ranging 15.4–86 nm in particle sizes, and microplastics with agglomerates were released each time the laser cutter lid was opened and were observed to gradually increase in concentration for a period of at least 20 min after the completion of a cut. The GC-MS gaseous samples primarily contained methyl methacrylate at a low level close to the detection limit of the infrared air analyzer.
Autor:innen und Institutionen
- Department of Environmental Health Sciences, Fielding School of Public Health, University of California-Los Angeles, Los Angeles, California 90095-1735, United States.
- Samueli School of Engineering, University of California-Los Angeles, Los Angeles, California 90095-1735, United States.
ORCID-Profile: Jacob Schmidt, Candace Su-Jung Tsai
Förderung
- NIEHS NIH HHS
- National Institute of Environmental Health Sciences
- University of California, Los Angeles
- National Institute for Occupational Safety and Health
Zitieren
APA
Munoz, A., Schmidt, J., Suffet, I. H. M., & Tsai, C. S. (2023). Characterization of Emissions from Carbon Dioxide Laser Cutting Acrylic Plastics. ACS Chemical Health & Safety, 30(4), 182-192. https://doi.org/10.1021/acs.chas.3c00013
Vancouver
Munoz A, Schmidt J, Suffet IHM, Tsai CS. Characterization of Emissions from Carbon Dioxide Laser Cutting Acrylic Plastics. ACS Chemical Health & Safety. 2023;30(4):182-192. doi:10.1021/acs.chas.3c00013
BibTeX
@article{Munoz2023,
author = {Munoz, Alejandro and Schmidt, Jacob and Suffet, I H Mel and Tsai, Candace Su-Jung},
title = {Characterization of Emissions from Carbon Dioxide Laser Cutting Acrylic Plastics},
journal = {ACS Chemical Health & Safety},
year = {2023},
volume = {30},
number = {4},
pages = {182--192},
doi = {10.1021/acs.chas.3c00013}
}
EUVIMED