EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 3.0

Effects of pre- and post-simulated home bleaching with 10% carbamide peroxide on the shear bond strengths of different adhesives to enamel

Aminah M. Elmourad, Mohammed Q. Alqahtani

The Saudi Journal for Dental Research · 2014

DOI: 10.1016/j.sjdr.2014.01.002 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Saudi Journal for Dental Research, 2014. Verfasst von Aminah M. Elmourad und 1 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 3.0). Gefördert von: College of Dentistry Research Center and Deanship of Scientific Research at King Saud University, Saudi Arabia.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This in vitro study was undertaken to investigate the effects of pre- and post-simulated bleaching procedures with 10% carbamide peroxide on the shear bond strengths of different adhesives to enamel and to determine the failure modes of tested specimens. The specimens were randomly divided into three groups (n = 30) according to the sequence of bleaching and bonding procedures (control non-bleach, pre- and post-bleach groups). Each group was then subdivided into three subgroups (n = 10) according to the three types of adhesives: OptiBond Solo Plus (Kerr) and Single Bond Universal (3M-ESPE) used as etch-and-rinse and self-etch techniques. Resin composite cylinders were then placed with Filtek Z 250 (3M ESPE). The specimens were stored in distilled water at 37 °C for 24 hours prior to being thermocycled for 1000 cycles (at 5 and 55 °C). The samples in the pre- and post-bleach groups were also immersed daily in artificial saliva at 37 °C, and for two weeks after completion of the bleaching process. Shear bond strengths were measured with a cross-head speeds of 0.5 mm/min. Failure modes of debonded specimens were determined by stereomicroscopy (30×). The interface margins of resin composite to the different enamel conditions were observed by scanning electron microscopy (1000×) before shear bond strength testing. There were no significant effects of different enamel conditions (control non-bleach, pre-bleach and post-bleach) on the shear bond strengths of OptiBond Solo Plus Adhesive Agent or etch-and-rinse Single Bond Universal Adhesive Agent. Pre- and post-simulated home bleaching of enamel with 10% carbamide peroxide had an adverse effect on the shear bond strengths of self-etch Single Bond Universal Adhesive Agent. In enamel, an etch-and-rinse approach with phosphoric acid remains the procedure of choice, since it guarantees the most durable bond to enamel. Therefore, selective phosphoric-acid-etching of enamel is highly recommended, followed by self-etching.

Förderung

  • College of Dentistry Research Center and Deanship of Scientific Research at King Saud University, Saudi Arabia

Zitieren

APA

Elmourad, A. M., & Alqahtani, M. Q. (2014). Effects of pre- and post-simulated home bleaching with 10% carbamide peroxide on the shear bond strengths of different adhesives to enamel. The Saudi Journal for Dental Research. https://doi.org/10.1016/j.sjdr.2014.01.002

Vancouver

Elmourad AM, Alqahtani MQ. Effects of pre- and post-simulated home bleaching with 10% carbamide peroxide on the shear bond strengths of different adhesives to enamel. The Saudi Journal for Dental Research. 2014. doi:10.1016/j.sjdr.2014.01.002

BibTeX
@article{Elmourad2014,
  author = {Elmourad, Aminah M. and Alqahtani, Mohammed Q.},
  title = {Effects of pre- and post-simulated home bleaching with 10% carbamide peroxide on the shear bond strengths of different adhesives to enamel},
  journal = {The Saudi Journal for Dental Research},
  year = {2014},
  doi = {10.1016/j.sjdr.2014.01.002}
}
Kostenlos starten →