Comparación de la precisión marginal de cofias de zirconia entre los sistemas CAD/CAM Cerec InLab (Sirona®), CAD/CAM Zirkonzahn (Zirkonzahn®) y sistema pantográfico Zirkograph 025 ECO (Zirkonzahn®)
Revista Odontológica Mexicana · 2015
DOI: 10.1016/j.rodmex.2015.10.005 ↗Kurz gefasst
Fachartikel in der Zeitschrift Revista Odontológica Mexicana, 2015. Verfasst von María José Jiménez Suárez und 2 weiteren Autor:innen. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).
Abstract (Originalsprache)
Objective
To compare marginal fit of zirconia copings manufactured following two different systems: CAD/CAM Cerec InLab (Sirona®) and Zirkonzahn (Zirkonzahn®) as well as a Zirkograph 025 ECO (Zirkonzahn®) pantograph system. Material and methods: A master Cr-Co model stump was manufactured; it was prepared for the zirconia crown of an upper premolar. Ten zirconia copings were manufactured for each group following manufacturer¿s instructions. Control group consisted on ten metallic copings. A replication technique was followed using elite HD+ polyvinyl siloxane (Zhermack®). Measurements were taken using a stereomicroscope at 50x magnification so as to obtain marginal width in microns and thus determine absolute marginal discrepancy of each coping. Statistical analysis was conducted using IBM SPSS® software. T-test study was conducted in order to compare obtained data.
Results
Mean marginal absolute discrepancy and marginal width were as follows: 92.14 ± 38.59 and 78.62 ± 31.33 μm for Cerec InLab (Sirona®) CAD/CAM system, 38.71 ± 12.62 and 36.91 ± 13.56 μm for Zirkonzahn (Zirkonzahn®) CAD/CAM system, 77.92 ± 38.01 and 69.42 ± 33.23 μm for Zirkograph 025 ECO (Zirkonzahn®) pantograph system. Control group made of metal copings exhibited 44.11 ± 15.36 and 43.74 ± 15.70 μm. With respect to absolute marginal discrepancy and marginal width, significant differences were observed when comparing Cerec InLab (Sirona®) and Zirkograph 025 ECO (Zirkonzahn®) with control group. Nevertheless, no significant differences were observed between Zirkonzahn (Zirkonzahn®) CAD/CAM system and the control group. Overall level of statistical significance was p > 0.001.
Conclusions
Zirkonzahn® CAD/CAM system was the most accurate system of all. CAD/CAM Cerec InLab system (Sirona®) proved to be the less precise system.
Zitieren
APA
Suárez, M. J. J., Vernimmen, F. S., & Merchán, E. A. R. (2015). Comparación de la precisión marginal de cofias de zirconia entre los sistemas CAD/CAM Cerec InLab (Sirona®), CAD/CAM Zirkonzahn (Zirkonzahn®) y sistema pantográfico Zirkograph 025 ECO (Zirkonzahn®). Revista Odontológica Mexicana. https://doi.org/10.1016/j.rodmex.2015.10.005
Vancouver
Suárez MJJ, Vernimmen FS, Merchán EAR. Comparación de la precisión marginal de cofias de zirconia entre los sistemas CAD/CAM Cerec InLab (Sirona®), CAD/CAM Zirkonzahn (Zirkonzahn®) y sistema pantográfico Zirkograph 025 ECO (Zirkonzahn®). Revista Odontológica Mexicana. 2015. doi:10.1016/j.rodmex.2015.10.005
BibTeX
@article{Surez2015,
author = {Suárez, María José Jiménez and Vernimmen, Fernando Sandoval and Merchán, Estefanía Alexandra Rodríguez},
title = {Comparación de la precisión marginal de cofias de zirconia entre los sistemas CAD/CAM Cerec InLab (Sirona®), CAD/CAM Zirkonzahn (Zirkonzahn®) y sistema pantográfico Zirkograph 025 ECO (Zirkonzahn®)},
journal = {Revista Odontológica Mexicana},
year = {2015},
doi = {10.1016/j.rodmex.2015.10.005}
}
EUVIMED