EUVIMEDEUVIMED entdecken
FallberichtOpen Access · CC BY-NC-ND 4.0

Evaluación biomecánica y análisis de clavo intramedular telescópico de fémur reutilizado en niño con acondroplasia

C M Posada, R D'Amato, M Galán-Olleros, C Miranda-Gorozarri, Á Palazón-Quevedo, J Alonso-Hernández

Revista Española de Cirugía Ortopédica y Traumatología · 2025

DOI: 10.1016/j.recot.2025.03.005 ↗

Kurz gefasst

Fallbericht in der Zeitschrift Revista Española de Cirugía Ortopédica y Traumatología, 2025. Verfasst von C M Posada und 5 weiteren Autor:innen. Beteiligte Einrichtung: Departamento de Ingeniería Mecánica, Química y Diseño Industrial, Escuela Técnica Superior de Ingeniería y Diseño Industrial, Universidad Politécnica…. Hauptthemen laut MEDLINE: Achondroplasia, Bone Nails, Bone Lengthening, Femur. Die Arbeit nennt 23 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

INTRODUCTION: Telescopic intramedullary nails (TIMN) have represented a significant advancement in limb lengthening procedures. However, their elongation capacity is limited to 5cm in the bones of patients with achondroplasia. Consequently, techniques involving TIMN reutilization have been developed. This reuse presents mechanical and safety challenges due to material fatigue and repetitive loading, which may compromise the structural integrity of the implant. This study evaluates the biomechanical performance and potential damage of a reused TIMN. METHODS: An experimental analysis was conducted on a TIMN removed after 2 5cm lengthening procedures in a patient with achondroplasia. The nail was measured and assessed following non-destructive deconstruction, material analysis, 3D modeling through reverse engineering, and finite element analysis to assess its behavior under different loading conditions. RESULTS: Mechanical and chemical damage was identified, compromising the nail's integrity. The aged Ti6Al4V alloy was validated for its resistance to complex loads. The 3D modeling showed that the gear mechanism effectively converted rotational movement into translational motion. The finite element analysis revealed that the safety factor reached its critical limit at angles of 2.44 and 2.25°, showing that the nail was nearing its resistance limit. The stem and guide were identified as critical components. CONCLUSIONS: TIMN reutilization must be performed with caution due to potential material fatigue. This study provides a foundation for redesigning these implants to improve their capacity to withstand prolonged loading cycles.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

AchondroplasiaBone NailsBone LengtheningFemurHumansBiomechanical PhenomenaFinite Element AnalysisChildMaterials TestingFracture Fixation, Intramedullary

Stichwörter der Autor:innen

AchondroplasiaAcondroplasiaCirugía de alargamiento de extremidadesClavos intramedulares telescópicosLimb lengthening surgeryShort statureTalla bajaTelescopic intramedullary nails

Autor:innen und Institutionen

  • Departamento de Ingeniería Mecánica, Química y Diseño Industrial, Escuela Técnica Superior de Ingeniería y Diseño Industrial, Universidad Politécnica de Madrid, Madrid, España.
  • Servicio de Cirugía Ortopédica y Traumatología, Hospital Infantil Universitario Niño Jesús, Madrid, España. Electronic address: mgalanolleros@gmail.com.
  • Servicio de Cirugía Ortopédica y Traumatología, Hospital Infantil Universitario Niño Jesús, Madrid, España.

Zitieren

APA

Posada, C. M., D'Amato, R., Galán-Olleros, M., Miranda-Gorozarri, C., Palazón-Quevedo, Á., & Alonso-Hernández, J. (2025). Evaluación biomecánica y análisis de clavo intramedular telescópico de fémur reutilizado en niño con acondroplasia. Revista Española de Cirugía Ortopédica y Traumatología. https://doi.org/10.1016/j.recot.2025.03.005

Vancouver

Posada CM, D'Amato R, Galán-Olleros M, Miranda-Gorozarri C, Palazón-Quevedo Á, Alonso-Hernández J. Evaluación biomecánica y análisis de clavo intramedular telescópico de fémur reutilizado en niño con acondroplasia. Revista Española de Cirugía Ortopédica y Traumatología. 2025. doi:10.1016/j.recot.2025.03.005

BibTeX
@article{Posada2025,
  author = {Posada, C M and D'Amato, R and Galán-Olleros, M and Miranda-Gorozarri, C and Palazón-Quevedo, Á and Alonso-Hernández, J},
  title = {Evaluación biomecánica y análisis de clavo intramedular telescópico de fémur reutilizado en niño con acondroplasia},
  journal = {Revista Española de Cirugía Ortopédica y Traumatología},
  year = {2025},
  doi = {10.1016/j.recot.2025.03.005}
}
Kostenlos starten →