EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Impact of resin tank, polishing, and thermal aging on the surface and optical properties of additively manufactured hard occlusal device resins

Mustafa Borga Dönmez, Timo Scherwey, Esma Başak Gül Aygün, Çiğdem Kahveci, Burak Yilmaz

The Journal of Prosthetic Dentistry · 2026

DOI: 10.1016/j.prosdent.2026.02.014 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2026. Verfasst von Mustafa Borga Dönmez und 4 weiteren Autor:innen. Beteiligte Einrichtung: Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Biruni University, İstanbul, Turkey; External Researcher, Department of Reco…. Hauptthemen laut MEDLINE: Dental Polishing, Resins, Synthetic, Dental Materials. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Additively manufactured occlusal devices typically require labor-intensive polishing to achieve clinically acceptable surfaces. However, limited evidence exists on whether newer resin tanks that are claimed to improve surface and optical properties can reduce this need or how polishing and aging interact to affect surface and optical outcomes. PURPOSE: The purpose of this in vitro study was to investigate the effects of resin type, resin tank selection, polishing procedures, and aging on the surface roughness (Ra), gloss, and light transmittance of additively manufactured occlusal device resins. MATERIAL AND METHODS: Eighty disk-shaped specimens (Ø30×2 mm) were additively manufactured from 2 hard occlusal device resins (Freeprint Splint 2.0, FPS and KeySplint Hard, KSH) using 2 different resin tanks (Universal [conventional] and Ultragloss [modified]) of a digital light processing 3-dimensional printer (MAX UV). After fabrication, the specimens were divided into 2 subgroups (nonpolished and polished) (n=10). Specimens in the polished group were manually polished with a pumice-water slurry followed by a polishing paste. After initial Ra, gloss, and light transmittance measurements, all specimens were subjected to thermocycling (10 000 cycles, 5 °C and 55 °C), and these measurements were repeated. Generalized linear model analyses and Bonferroni-corrected post hoc tests were used for statistical analysis (α=.05). RESULTS: Polished specimens showed lower Ra than nonpolished specimens, and the modified tray led to lower Ra than the conventional tray for nonpolished specimens (P≤.005). FPS showed higher gloss than KSH when fabricated with the conventional tray and polished (P=.031). Nonpolished FPS and KSH specimens and polished KSH specimens had higher gloss when the modified tray was used (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental PolishingResins, SyntheticDental MaterialsSurface PropertiesMaterials TestingHumansIn Vitro TechniquesPrinting, Three-Dimensional

Substanzen

Resins, SyntheticDental Materials

Autor:innen und Institutionen

  • Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Biruni University, İstanbul, Turkey; External Researcher, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, Uni…
  • Dr med dent Candidate, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland.
  • Professor, Department of Prosthodontics, Faculty of Dentistry, Çukurova University, Adana, Turkey.
  • Private Practice, Ordu Oral and Dental Health Center, Ordu, Turkey.
  • Professor, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland; and Professor, Department of Restorative, Preventive and Pediatric Dentistry, School…

Zitieren

APA

Dönmez, M. B., Scherwey, T., Gül Aygün, E. B., Kahveci, Ç., & Yilmaz, B. (2026). Impact of resin tank, polishing, and thermal aging on the surface and optical properties of additively manufactured hard occlusal device resins. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2026.02.014

Vancouver

Dönmez MB, Scherwey T, Gül Aygün EB, Kahveci Ç, Yilmaz B. Impact of resin tank, polishing, and thermal aging on the surface and optical properties of additively manufactured hard occlusal device resins. The Journal of Prosthetic Dentistry. 2026. doi:10.1016/j.prosdent.2026.02.014

BibTeX
@article{Dnmez2026,
  author = {Dönmez, Mustafa Borga and Scherwey, Timo and Gül Aygün, Esma Başak and Kahveci, Çiğdem and Yilmaz, Burak},
  title = {Impact of resin tank, polishing, and thermal aging on the surface and optical properties of additively manufactured hard occlusal device resins},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2026},
  doi = {10.1016/j.prosdent.2026.02.014}
}
Kostenlos starten →