EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Flexural and structural behavior of additively manufactured zirconia: Influence of firing process and build orientation

Gabriela Panca Sabatini, Mustafa Borga Donmez, Pedro Molinero-Mourelle, Gülce Çakmak, Mehmet Esad Güven, Ahmet Burçin Batıbay, Newton Sesma, Burak Yilmaz

The Journal of Prosthetic Dentistry · 2026

DOI: 10.1016/j.prosdent.2025.10.043 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2026. Verfasst von Gabriela Panca Sabatini und 7 weiteren Autor:innen. Beteiligte Einrichtung: Clinical Assistant, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland. Hauptthemen laut MEDLINE: Zirconium, Yttrium, Flexural Strength, Dental Materials. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Additive manufacturing of zirconia is gaining popularity in dentistry; however, knowledge of the influence of build orientation and firing process on its mechanical properties and structural behavior remains limited. PURPOSE: The purpose of this in vitro study was to compare the effect of firing process and build orientation on the flexural strength (FS) and structural characteristics of additively manufactured 3% mol yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP) with subtractively manufactured 3Y-TZP and 4Y-TZP. MATERIAL AND METHODS: A total of 192 bar-shaped (17×4×1.5 mm) and 16 disk-shaped (Ø10×1.5 mm) specimens were manufactured either additively with a 3Y-TZP slurry (INNI Cera) or subtractively with presintered 3Y-TZP (IPS e.max ZirCAD LT [SM-LT]) or 4Y-TZP (IPS e.max ZirCAD MT [SM-MT]) zirconia disks. The additively manufactured specimens were categorized based on build orientation (0-degree [AMH], 45-degree [AMD], and 90-degree [AMV]) and firing process (combined [1-step] or separate [2-step] debinding and sintering cycle). All specimens were divided into 2 groups (n=12 for bar-shaped and n=1 for disk-shaped specimens) of aged (thermocycling for 10 000 cycles between 5 °C and 55 °C) and nonaged. Bar-shaped specimens were tested for FS, while disk-shaped specimens were used for structural characterization using X-ray diffraction (XRD) and scanning electron microscope (SEM) imaging. The FS data were analyzed with general linear model analysis and Bonferroni-corrected post hoc tests (α=.05). RESULTS: The interaction between manufacturing protocol and aging condition affected the FS values (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumYttriumFlexural StrengthDental MaterialsMaterials TestingIn Vitro TechniquesSurface PropertiesDental Stress Analysis

Substanzen

ZirconiumYttriumzirconium oxideDental Materialsyttria stabilized tetragonal zirconia

Autor:innen und Institutionen

  • Clinical Assistant, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland.
  • Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Biruni University, İstanbul, Turkey; and External Researcher, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine,…
  • Senior Lecturer, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland; and Senior Lecturer, Department of Conservative Dentistry and Prosthodontics,…
  • Senior Research Associate, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland; and Head of the Digital Dental Technology Laboratory, Department of…
  • Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Necmettin Erbakan University, Konya, Turkey.
  • Senior Engineer, R&D and Technology Directorate, Mechanical and Chemical Industry Corporation, Ankara, Turkey.

Zitieren

APA

Sabatini, G. P., Donmez, M. B., Molinero-Mourelle, P., Çakmak, G., Güven, M. E., Batıbay, A. B., Sesma, N., & Yilmaz, B. (2026). Flexural and structural behavior of additively manufactured zirconia: Influence of firing process and build orientation. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2025.10.043

Vancouver

Sabatini GP, Donmez MB, Molinero-Mourelle P, Çakmak G, Güven ME, Batıbay AB, et al. Flexural and structural behavior of additively manufactured zirconia: Influence of firing process and build orientation. The Journal of Prosthetic Dentistry. 2026. doi:10.1016/j.prosdent.2025.10.043

BibTeX
@article{Sabatini2026,
  author = {Sabatini, Gabriela Panca and Donmez, Mustafa Borga and Molinero-Mourelle, Pedro and Çakmak, Gülce and Güven, Mehmet Esad and Batıbay, Ahmet Burçin and Sesma, Newton and Yilmaz, Burak},
  title = {Flexural and structural behavior of additively manufactured zirconia: Influence of firing process and build orientation},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2026},
  doi = {10.1016/j.prosdent.2025.10.043}
}
Kostenlos starten →