EUVIMEDEUVIMED entdecken
Crossref

Wear resistance of additive-manufactured denture teeth following mastication simulation

Marissa Gentle, Tariq Alsahafi, Rafiullah Bashiri, Amara Abreu-Serrano, Taiseer A Sulaiman

The Journal of Prosthetic Dentistry · 2026-02 · 135 (2) · 390.e1-390.e7

DOI: 10.1016/j.prosdent.2025.09.026 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2026-02. Verfasst von Marissa Gentle und 4 weiteren Autor:innen. Beteiligte Einrichtung: Graduate student, Graduate Prosthodontics, Department of Restorative Sciences, Adams School of Dentistry, University of North Carolina at Chapel Hill…. Hauptthemen laut MEDLINE: Dental Restoration Wear, Tooth, Artificial, Mastication, Denture Design. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 23 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Denture teeth have traditionally been made from polymethyl methacrylate (PMMA) material. The introduction of subtractive manufacturing enabled the milling of denture teeth, and the advent of additive manufacturing (AM) enabled the 3-dimensional (3D) printing of denture teeth. However, the wear resistance of 3D printed denture teeth is unknown. PURPOSE: The purpose of this in vitro study was to compare the linear and volumetric wear of AM resins of different compositions with conventional double cross-linked (DCL) PMMA denture teeth and natural enamel. MATERIAL AND METHODS: DCL PMMA second mandibular premolar denture teeth (Ivoclar Ortholingual conventional DCL PMMA resin teeth) and natural human enamel specimens were used as controls (n=8). The DCL teeth were scanned and printed in 3 different AM resin materials. The specimens DCL PMMA resin teeth (DCL), natural human enamel (enamel), VarseoSmile Crown Plus (AM-CFH), DENTCA Denture Teeth (AM-MPR), a diurethane dimethacrylate (DUDMA) photopolymerizable resin, and OnX Tough (AM-NCH), labeled a hybrid ceramic resin, underwent mastication simulation in a biaxial fatigue testing machine. The mastication simulator was set at 1.53 Hz, thermocycling between 5 °C and 55 °C, and 49 N against a Ø6-mm steatite antagonist following the International Organization for Standardization Technical Specification (ISO/TS) 14569-2. After 250 000 cycles, the linear and volumetric changes on the occlusal surfaces of the specimens were analyzed with a 2-way analysis of variance (ANOVA), followed by a Tukey comparison test (α=.05). RESULTS: A statistically significant difference in linear and volumetric wear was found between enamel, DCL, and AM denture teeth (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental Restoration WearTooth, ArtificialMasticationDenture DesignHumansPolymethyl MethacrylateIn Vitro TechniquesPrinting, Three-DimensionalDental EnamelMaterials TestingDental MaterialsDental Stress Analysis

Substanzen

Polymethyl MethacrylateDental Materials

Autor:innen und Institutionen

  • Graduate student, Graduate Prosthodontics, Department of Restorative Sciences, Adams School of Dentistry, University of North Carolina at Chapel Hill, Chapel Hill, NC.
  • Oral and Craniofacial Biomedicine PhD Candidate and Teaching Assistant, Division of Comprehensive Oral Health, Adams School of Dentistry, University of North Carolina at Chapel Hill, Chapel Hill, NC; and Lecturer, Depar…
  • Assistant Professor, Prosthodontics, Department of Restorative Sciences, Adams School of Dentistry, University of North Carolina at Chapel Hill, Chapel Hill, NC.
  • Professor and Director of Advanced Education in Prosthodontics, Department of Restorative Sciences, Adams School of Dentistry, University of North Carolina at Chapel Hill, Chapel Hill, NC.
  • Associate Professor, Department of Restorative Sciences, Adams School of Dentistry, University of North Carolina at Chapel Hill, Chapel Hill, NC. Electronic address: sulaiman@unc.edu.

Zitieren

APA

Gentle, M., Alsahafi, T., Bashiri, R., Abreu-Serrano, A., & Sulaiman, T. A. (2026). Wear resistance of additive-manufactured denture teeth following mastication simulation. The Journal of Prosthetic Dentistry, 135(2), 390.e1-390.e7. https://doi.org/10.1016/j.prosdent.2025.09.026

Vancouver

Gentle M, Alsahafi T, Bashiri R, Abreu-Serrano A, Sulaiman TA. Wear resistance of additive-manufactured denture teeth following mastication simulation. The Journal of Prosthetic Dentistry. 2026;135(2):390.e1-390.e7. doi:10.1016/j.prosdent.2025.09.026

BibTeX
@article{Gentle2026,
  author = {Gentle, Marissa and Alsahafi, Tariq and Bashiri, Rafiullah and Abreu-Serrano, Amara and Sulaiman, Taiseer A},
  title = {Wear resistance of additive-manufactured denture teeth following mastication simulation},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2026},
  volume = {135},
  number = {2},
  pages = {390.e1--390.e7},
  doi = {10.1016/j.prosdent.2025.09.026}
}
Kostenlos starten →