EUVIMEDEUVIMED entdecken
Crossref

Evaluation of methods for removing stains from a 3D printed resin for denture teeth

Giovanna Bueno de Souza, Hamile Emanuella do Carmo Viotto, João Fernando Carrijo Queiroz, Larianne de Sousa Moisés, Sabrina Romão Gonçalves Coelho, Danny Omar Mendoza Marin, Ana Carolina Pero

The Journal of Prosthetic Dentistry · 2026-02 · 135 (2) · 392.e1-392.e8

DOI: 10.1016/j.prosdent.2025.09.022 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2026-02. Verfasst von Giovanna Bueno de Souza und 6 weiteren Autor:innen. Beteiligte Einrichtung: Predoctoral student, Department of Dental Materials and Prosthodontics, Araraquara Dental School, São Paulo State University (UNESP), Araraquara, Bra…. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Tooth, Artificial. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 68 Literaturangaben. Gefördert von: Fundação de Amparo à Pesquisa do Estado de São Paulo.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: An efficient protocol for removing stains from 3-dimensionally (3D) printed artificial teeth must also preserve their surface properties. PURPOSE: The purpose of this in vitro study was to evaluate methods of removing stains from a 3D printed resin (Bio Crown) for artificial teeth submitted to immersion in coffee by using spectrophotometric analysis (CIEDE2000) and analyzing surface roughness with a profilometer and topography with a scanning electron microscope (SEM). MATERIAL AND METHODS: Disks (Ø10×1.2 mm) were 3D printed and stained in instant coffee simulating 1 year of consumption. Color data (L*, a*, b*) and roughness (Ra, µm) were obtained at T0 (baseline, before staining), T1 (after staining), and T2 (after each stain removal protocol, n=12). The stain removal groups used sodium perborate (SP), 0.25% sodium hypochlorite (SH), conventional polishing with brush and pumice stone + felt wheels and universal paste (CP), and polishing with 3-abrasive tip kit (AP); the control was storage in distilled water (DW). Mixed 2-way ANOVA followed by the Bonferroni test was performed to statistically analyzing data with α=.05. RESULTS: Roughness increased in all groups between T1 and T2 (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalTooth, ArtificialSurface PropertiesCoffeeIn Vitro TechniquesHumansDental PolishingMicroscopy, Electron, ScanningSodium HypochloriteBoratesSpectrophotometry

Substanzen

CoffeeSodium Hypochloritesodium perborateBorates

Autor:innen und Institutionen

  • Predoctoral student, Department of Dental Materials and Prosthodontics, Araraquara Dental School, São Paulo State University (UNESP), Araraquara, Brazil.
  • Doctoral student, Department of Dental Materials and Prosthodontics, Araraquara Dental School, São Paulo State University (UNESP), Araraquara, Brazil.
  • Master's student, Department of Dental Materials and Prosthodontics, Araraquara Dental School, São Paulo State University (UNESP), Araraquara, Brazil.
  • Associate Professor, Department of Dentistry, Health Sciences Center, Santa Catarina Federal University, Florianópolis, Brazil.
  • Associate Professor, Department of Dental Materials and Prosthodontics, Araraquara Dental School, São Paulo State University (UNESP), Araraquara, Brazil. Electronic address: ana.pero@unesp.br.

Förderung

  • Fundação de Amparo à Pesquisa do Estado de São Paulo

Zitieren

APA

de Souza, G. B., Viotto, H. E. D. C., Queiroz, J. F. C., Moisés, L. S., Coelho, S. R. G., Marin, D. O. M., & Pero, A. C. (2026). Evaluation of methods for removing stains from a 3D printed resin for denture teeth. The Journal of Prosthetic Dentistry, 135(2), 392.e1-392.e8. https://doi.org/10.1016/j.prosdent.2025.09.022

Vancouver

de Souza GB, Viotto HEDC, Queiroz JFC, Moisés LS, Coelho SRG, Marin DOM, et al. Evaluation of methods for removing stains from a 3D printed resin for denture teeth. The Journal of Prosthetic Dentistry. 2026;135(2):392.e1-392.e8. doi:10.1016/j.prosdent.2025.09.022

BibTeX
@article{deSouza2026,
  author = {de Souza, Giovanna Bueno and Viotto, Hamile Emanuella do Carmo and Queiroz, João Fernando Carrijo and Moisés, Larianne de Sousa and Coelho, Sabrina Romão Gonçalves and Marin, Danny Omar Mendoza and Pero, Ana Carolina},
  title = {Evaluation of methods for removing stains from a 3D printed resin for denture teeth},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2026},
  volume = {135},
  number = {2},
  pages = {392.e1--392.e8},
  doi = {10.1016/j.prosdent.2025.09.022}
}
Kostenlos starten →