Analysis of flexural strength and Weibull modulus of printed and milled zirconia: A systematic review
The Journal of Prosthetic Dentistry · 2025-09 · 134 (3) · 628.e1-628.e8
DOI: 10.1016/j.prosdent.2025.05.032 ↗Kurz gefasst
Systematische Übersicht in der Zeitschrift The Journal of Prosthetic Dentistry, 2025-09. Verfasst von Ligia Antunes Pereira Pinelli und 2 weiteren Autor:innen. Beteiligte Einrichtung: Professor, Department of Dental Materials and Prosthodontics, School of Dentistry of Araraquara, Sao Paulo State University (UNESP), Araraquara, Braz…. Hauptthemen laut MEDLINE: Zirconium, Flexural Strength, Printing, Three-Dimensional, Dental Materials. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 63 Literaturangaben.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: Additive manufacturing (AM) has been used for zirconia dental prostheses, but studies that evaluated mechanical properties in comparison with subtractive manufacturing (SM), such as flexural strength (FS) and Weibull modulus (m), are lacking. PURPOSE: The purpose of this systematic review was to evaluate studies comparing the FS and m of zirconia produced by AM and SM. MATERIAL AND METHODS: Searches were conducted in the PubMed, Science Direct, Embase, Web of Science, and Scopus databases, with the keywords zirconium, "zirconium oxide," "3D printing," "additive manufacturing," "additive manufacture," flexural, "flexural strength" from 2019 to 2024, enriched with manual searches. RESULTS: Few AM technologies are currently available to print dental zirconia, with the most used being stereolithography (SLA), digital light processing (DLP), and lithography-based ceramic manufacturing (LCM) systems. In general, specimens obtained by milling were found to have a higher FS and m than printed specimens. CONCLUSIONS: Printed zirconia has great potential for use in oral rehabilitation because, although its flexural strength and Weibull modulus are lower than those of subtractively manufactured zirconia, they still should provide adequate clinical performance.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Professor, Department of Dental Materials and Prosthodontics, School of Dentistry of Araraquara, Sao Paulo State University (UNESP), Araraquara, Brazil.
- Predoctoral student, Department of Dental Materials and Prosthesis, Ribeirão Preto School of Dentistry, University of São Paulo (USP), Ribeirão Preto, SP, Brazil.
- Professor, Department of Dental Materials and Prosthesis, Ribeirão Preto School of Dentistry, University of São Paulo (USP), Ribeirão Preto, SP, Brazil. Electronic address: andreare73@yahoo.com.br.
Zitieren
APA
Pinelli, L. A. P., Ferreira, I., & Reis, A. C. D. (2025). Analysis of flexural strength and Weibull modulus of printed and milled zirconia: A systematic review. The Journal of Prosthetic Dentistry, 134(3), 628.e1-628.e8. https://doi.org/10.1016/j.prosdent.2025.05.032
Vancouver
Pinelli LAP, Ferreira I, Reis ACD. Analysis of flexural strength and Weibull modulus of printed and milled zirconia: A systematic review. The Journal of Prosthetic Dentistry. 2025;134(3):628.e1-628.e8. doi:10.1016/j.prosdent.2025.05.032
BibTeX
@article{Pinelli2025,
author = {Pinelli, Ligia Antunes Pereira and Ferreira, Izabela and Reis, Andrea Cândido Dos},
title = {Analysis of flexural strength and Weibull modulus of printed and milled zirconia: A systematic review},
journal = {The Journal of Prosthetic Dentistry},
year = {2025},
volume = {134},
number = {3},
pages = {628.e1--628.e8},
doi = {10.1016/j.prosdent.2025.05.032}
}
EUVIMED