EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Effect of print orientation on sorption, solubility, and monomer elution of 3D printed resin restorative materials

Shaymaa Mudhaffer, Nick Silikas, Julian Satterthwaite

The Journal of Prosthetic Dentistry · 2025

DOI: 10.1016/j.prosdent.2025.04.040 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift The Journal of Prosthetic Dentistry, 2025. Verfasst von Shaymaa Mudhaffer und 2 weiteren Autor:innen. Beteiligte Einrichtung: PhD student, Division of Dentistry, School of Medical Sciences, University of Manchester, Manchester, UK. Electronic address: S.mudhaffer@Taibahu.edu…. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Composite Resins, Dental Materials, Dental Restoration Repair. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 71 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Royal Embassy of Saudi Arabia Cultural Bureau in London.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: The long-term stability and clinical safety of 3 dimensional (3D) printed dental restorative resins in the oral cavity remains uncertain, despite their increased use. PURPOSE: The purpose of this in vitro study was to evaluate the impact of different printing orientations on the sorption, solubility, and monomer elution of various 3D printed definitive and interim dental restorative resins compared with that of milled resin materials. MATERIAL AND METHODS: Two 3D printed materials for definitive restoration, VarseoSmile Crownplus (VCP) and Crowntec (CT) and 3 for interim restorations, C&B MFH (ND), Dima C&B temp (DT), and GC temp print (GC), were additively manufactured in 3 orientations (0, 45, and 90 degrees). A digital light processing (DLP) 3D printer (ASIGA MAX UV) was used with postprocessing parameters as per the manufacturers' recommendations. Specimens for sorption and solubility (14×14×1 mm) were stored in artificial saliva at 37 °C and measured over a 90-day period (n=6). Specimens used for monomer elution (14×14×2 mm) were stored in a 75% ethanol and water (E/W) solution, and elution was assessed after 1 and 7 days using ultra-high performance liquid chromatography coupled with mass spectrometry (UHPLC/MS) (n=4). Milled materials, Lava Ultimate (LU) and Telio CAD (TC), were used as controls. Multiple way ANOVA, 1-way ANOVA, and Tukey HSD post hoc tests (α=.05) were used to analyze the data. RESULTS: Printing orientation significantly influenced the sorption and solubility of 3D printed resins (P=.008) but did not influence their monomer elution (P=.774). All materials met the recommended International Organization for Standardization (ISO) 4049 standards for sorption and solubility, except ND, which exceeded the maximum recommended sorption value (57.1 μg/mm3). The 3D printed interim materials ND, DT, and GC exhibited greater sorption (27.3-57.1 μg/mm3), solubility (2.6-3.6 μg/mm3), and monomer elution (53.2-87.4 μmol/L) compared with the definitive materials VCP (9.8-0.9 μg/mm3, 50.5 μmol/L) and CT (9.4-0.02 μg/mm3, 51.3 μmol/L). All 3D printed resins exhibited lower sorption (9.4-30.1 μg/mm3) but significantly higher monomer elution (50.5-87.4 μmol/L) compared with LU (36.1 μg/mm3, 7.6 μmol/L), except for ND, which had the highest sorption values (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalComposite ResinsDental MaterialsDental Restoration RepairHumansIn Vitro TechniquesMaterials TestingSolubilitySaliva, Artificial

Substanzen

Composite ResinsDental MaterialsSaliva, Artificial

Autor:innen und Institutionen

  • PhD student, Division of Dentistry, School of Medical Sciences, University of Manchester, Manchester, UK. Electronic address: S.mudhaffer@Taibahu.edu.sa.
  • Full Professor, Division of Dentistry, School of Medical Sciences, University of Manchester, Manchester, UK.

Förderung

  • Royal Embassy of Saudi Arabia Cultural Bureau in London

Zitieren

APA

Mudhaffer, S., Silikas, N., & Satterthwaite, J. (2025). Effect of print orientation on sorption, solubility, and monomer elution of 3D printed resin restorative materials. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2025.04.040

Vancouver

Mudhaffer S, Silikas N, Satterthwaite J. Effect of print orientation on sorption, solubility, and monomer elution of 3D printed resin restorative materials. The Journal of Prosthetic Dentistry. 2025. doi:10.1016/j.prosdent.2025.04.040

BibTeX
@article{Mudhaffer2025,
  author = {Mudhaffer, Shaymaa and Silikas, Nick and Satterthwaite, Julian},
  title = {Effect of print orientation on sorption, solubility, and monomer elution of 3D printed resin restorative materials},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2025},
  doi = {10.1016/j.prosdent.2025.04.040}
}
Kostenlos starten →