EUVIMEDEUVIMED entdecken
Crossref

Physical and mechanical properties of various resins for additively manufactured definitive fixed dental restorations: Effect of material type and thermal cycling

Abdulaziz Alhotan, Ahmed Mahmoud Fouda, Hanan Al-Johani, Hyung-In Yoon, Jukka P Matinlinna

The Journal of Prosthetic Dentistry · 2025

DOI: 10.1016/j.prosdent.2025.02.042 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025. Verfasst von Abdulaziz Alhotan und 4 weiteren Autor:innen. Beteiligte Einrichtung: Assistant Professor, Department of Dental Health, College of Applied Medical Sciences, King Saud University, Riyadh, Saudi Arabia. Hauptthemen laut MEDLINE: Composite Resins, Dental Restoration, Permanent, Dental Materials. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 47 Literaturangaben. Gefördert von: King Saud University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Although additive manufacturing (AM) has facilitated the fabrication of resin-based definitive restorations, knowledge of the effects of artificial aging on their physical and mechanical properties is lacking. PURPOSE: The purpose of this in vitro study was to investigate the effects of material type and thermal cycling on the translucency, surface roughness, microhardness, and flexural strength of AM resins marketed for definitive restorations. MATERIAL AND METHODS: Bar-shaped (25×2×2 mm) and disk-shaped (Ø10×2 mm) specimens from 4 different AM resin groups Crowntec (CT), Tera Harz TC-80DP (TH), VarseoSmile Crown plus (VS), and Permanent (CB) were prepared. The specimens were randomly distributed to 2 groups: (1) nonaged (stored in distilled water at 37 °C for 24 hours) and (2) aged (thermocycled for 10 000 cycles at 5 °C to 55 °C). For each specimen, the degree of conversion (DC) was determined using Fourier transform infrared spectroscopy. Color coordinates of the specimens were measured to calculate relative translucency parameter (RTP) values. Surface roughness (Ra) was measured with an optical profilometer, and Vickers microhardness values (VHN) were obtained. Flexural strength (σ) and elastic modulus (E) values were obtained by using the 3-point bend test. Scanning electron microscopy (SEM) was used to analyze the fractured surfaces. The data were statistically analyzed using factorial analysis of variance (ANOVA), followed by Tukey post hoc analyses and paired t tests (α=.05). RESULTS: Both DC and RTP were significantly affected by material type (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Composite ResinsDental Restoration, PermanentDental MaterialsSurface PropertiesMaterials TestingFlexural StrengthHardnessIn Vitro TechniquesHumansTemperatureSpectroscopy, Fourier Transform Infrared

Substanzen

Composite ResinsDental Materials

Autor:innen und Institutionen

  • Assistant Professor, Department of Dental Health, College of Applied Medical Sciences, King Saud University, Riyadh, Saudi Arabia.
  • Senior Researcher, Department of Oral Technology, Medical Faculty, University Hospital Bonn, Bonn, North Rhine-Westphalia, Germany; and Lecturer, Department of Fixed Prosthodontics, Suez Canal University, Ismailia, Egyp…
  • Assistant Professor, Department of Restorative Dentistry, Faculty of Dentistry, King Abdulaziz University, Jeddah, Saudi Arabia.
  • Associate Professor, Department of Prosthodontics, School of Dentistry and Dental Research Institute, Seoul National University, Seoul, Republic of Korea; and Visiting Professor, Department of Reconstructive Dentistry a…
  • Professor, Division of Dentistry, School of Medical Sciences, University of Manchester, Manchester, UK.

Förderung

  • King Saud University

Zitieren

APA

Alhotan, A., Fouda, A. M., Al-Johani, H., Yoon, H. I., & Matinlinna, J. P. (2025). Physical and mechanical properties of various resins for additively manufactured definitive fixed dental restorations: Effect of material type and thermal cycling. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2025.02.042

Vancouver

Alhotan A, Fouda AM, Al-Johani H, Yoon HI, Matinlinna JP. Physical and mechanical properties of various resins for additively manufactured definitive fixed dental restorations: Effect of material type and thermal cycling. The Journal of Prosthetic Dentistry. 2025. doi:10.1016/j.prosdent.2025.02.042

BibTeX
@article{Alhotan2025,
  author = {Alhotan, Abdulaziz and Fouda, Ahmed Mahmoud and Al-Johani, Hanan and Yoon, Hyung-In and Matinlinna, Jukka P},
  title = {Physical and mechanical properties of various resins for additively manufactured definitive fixed dental restorations: Effect of material type and thermal cycling},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2025},
  doi = {10.1016/j.prosdent.2025.02.042}
}
Kostenlos starten →