Surface roughness, wear, and abrasiveness of printed and milled occlusal veneers after thermomechanical aging
The Journal of Prosthetic Dentistry · 2024
DOI: 10.1016/j.prosdent.2024.07.012 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2024. Verfasst von Noha Morsy und 3 weiteren Autor:innen. Beteiligte Einrichtung: Fixed Prosthodontics, Department of Conservative Dentistry, Alexandria University, Alexandria, Egypt. Electronic address: noha.moursy@alexu.edu.eg. Hauptthemen laut MEDLINE: Dental Veneers, Surface Properties, Dental Porcelain, Ceramics. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 43 Literaturangaben.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: Occlusal veneers are a conservative method of reestablishing vertical dimensions of occlusion (VDO) for worn teeth. A restorative material used for occlusal veneers should have a smooth surface, adequate wear resistance, and low abrasiveness to the antagonists, as total wear of occlusal veneers and their antagonists determines the stability of the reestablished VDO. Studies on roughness, wear, and abrasiveness of occlusal veneers are scarce. PURPOSE: The purpose of this in vitro study was to assess the surface roughness, wear, and abrasiveness of printed and milled occlusal veneers after thermomechanical aging against natural cusps and restorative materials. MATERIAL AND METHODS: Forty-eight extracted mandibular first molars were prepared for occlusal veneers and scanned with an intraoral scanner. The scans were exported to a computer-aided design program to design the occlusal veneers in 3 groups (n=16) according to the restorative material: group IP: milled lithium disilicate; group EN: milled hybrid ceramic (Vita Enamic), group VA: printed hybrid ceramic (Varseosmile Crown plus). The occlusal veneers in each group were bonded to their corresponding abutments and subjected to 250 000 mechanical cycles and a simultaneous 1000 thermal cycles in a mastication simulator. During thermomechanical aging, half of the specimens of each study group (n=8) were opposed by natural cusps (antagonist C) and the other half by antagonist cusps fabricated from the same restorative material as the occlusal veneers (antagonist R). The wear of the occlusal veneers and their antagonists was assessed with a 3-dimensional processing software program. The surface roughness of the veneers was assessed with a contact profilometer. The results were statistically analyzed with a 2-way ANOVA followed by the post hoc Tukey HSD test (α=.05). RESULTS: The 2-way ANOVA indicated a significant effect for the material and the antagonist on surface roughness, wear, and abrasiveness (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Fixed Prosthodontics, Department of Conservative Dentistry, Alexandria University, Alexandria, Egypt. Electronic address: noha.moursy@alexu.edu.eg.
- Fixed prosthodontics, Department of Conservative Dentistry, Alexandria University, Alexandria, Egypt.
- Conservative Dentistry, Department of Conservative Dentistry, Alexandria University, Alexandria, Egypt.
Zitieren
APA
Morsy, N., El Kateb, M., Ghoneim, M. M., & Holiel, A. A. (2024). Surface roughness, wear, and abrasiveness of printed and milled occlusal veneers after thermomechanical aging. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2024.07.012
Vancouver
Morsy N, El Kateb M, Ghoneim MM, Holiel AA. Surface roughness, wear, and abrasiveness of printed and milled occlusal veneers after thermomechanical aging. The Journal of Prosthetic Dentistry. 2024. doi:10.1016/j.prosdent.2024.07.012
BibTeX
@article{Morsy2024,
author = {Morsy, Noha and El Kateb, Mohammed and Ghoneim, Mona Mohamed and Holiel, Ahmed A},
title = {Surface roughness, wear, and abrasiveness of printed and milled occlusal veneers after thermomechanical aging},
journal = {The Journal of Prosthetic Dentistry},
year = {2024},
doi = {10.1016/j.prosdent.2024.07.012}
}
EUVIMED