EUVIMEDEUVIMED entdecken
Crossref

Effect of surface roughness and biofilm formation on the color properties of resin-infiltrated ceramic and lithium disilicate glass-ceramic CAD-CAM materials

Sümeyra Topçu, Neslihan Tekçe, Dilan Kopuz, Eda Yazıcı Özcelik, Fetiye Kolaylı, Safa Tuncer, Mustafa Demirci

The Journal of Prosthetic Dentistry · 2024

DOI: 10.1016/j.prosdent.2024.02.005 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2024. Verfasst von Sümeyra Topçu und 6 weiteren Autor:innen. Beteiligte Einrichtung: Research Assistant, Department of Restorative Dentistry, Kocaeli University, Kocaeli, Turkey. Hauptthemen laut MEDLINE: Computer-Aided Design, Biofilms, Surface Properties, Ceramics. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 36 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Computer-aided design and computer-aided manufacturing (CAD-CAM) materials have become popular for dental restorations; however, which materials should be preferred in terms of surface properties after biofilm formation is unclear. PURPOSE: The purpose of this in vitro study was to investigate the effect of biofilm formation on the discoloration properties of resin-infiltrated ceramic and glass-ceramic CAD-CAM materials and human teeth and to examine the effect of the brushing procedure on color change. MATERIAL AND METHODS: One hundred and six 2-mm-thick specimens were prepared from IPS e.max CAD and Cerasmart, and a total of 53 intact human teeth were used. Five specimens from each group were used to measure the amount of live biomass in the biofilm. The remaining 48 specimens in each group were divided into 4 subgroups: kept in distilled water without the formation of dental biofilm (DW), kept in tea without the formation of dental biofilm (T), kept in distilled water after the formation of dental biofilm (DWB), and kept in tea after the formation of dental biofilm (TB) (n=12). After finishing and polishing the materials, initial color measurements were made using a spectrophotometer, and surface roughness measurements were made using noncontact profilometer. After creating a biofilm layer in DWB and TB, all specimens were kept in their solutions at 37 °C for 24 hours, and the color measurements were repeated. After the biofilm layer had been removed by brushing, a third color measurement was made. The data were statistically analyzed with one-way analysis of variance (ANOVA) and two-way ANOVA (α=.05). RESULTS: The lowest roughness value was observed in Cerasmart. Tooth-IPS e.max CAD gave similar results. The Cerasmart material had the most viable biomass, whereas the IPS e.max CAD material had the least. TB had the highest ΔE1 value for all materials and DW had the lowest (P 1.8), and immersion in tea led to greater color change. The adhesion of biofilm to restorative dental materials plays an important role in the coloring of these dental materials.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Computer-Aided DesignBiofilmsSurface PropertiesCeramicsDental PorcelainColorHumansMaterials TestingIn Vitro TechniquesDental MaterialsToothbrushingResins, Synthetic

Substanzen

Dental Porcelainlithia disilicateGlass ceramicsDental MaterialsIPS e.max CAD LTResins, Synthetic

Autor:innen und Institutionen

  • Research Assistant, Department of Restorative Dentistry, Kocaeli University, Kocaeli, Turkey.
  • Professor, Department of Restorative Dentistry, Kocaeli University, Kocaeli, Turkey.
  • Assistant Professor, Department of Restorative Dentistry, Istanbul Kent University, Istanbul, Turkey. Electronic address: dilan.kopuz@kent.edu.tr.
  • Research Assistant, Department of Microbiology and Clinical Microbiology, Kocaeli University, Kocaeli, Turkey.
  • Professor, Department of Microbiology and Clinical Microbiology, Kocaeli University, Kocaeli, Turkey.
  • Professor, Department of Restorative Dentistry, Istanbul University, Istanbul, Turkey.

Zitieren

APA

Topçu, S., Tekçe, N., Kopuz, D., Özcelik, E. Y., Kolaylı, F., Tuncer, S., & Demirci, M. (2024). Effect of surface roughness and biofilm formation on the color properties of resin-infiltrated ceramic and lithium disilicate glass-ceramic CAD-CAM materials. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2024.02.005

Vancouver

Topçu S, Tekçe N, Kopuz D, Özcelik EY, Kolaylı F, Tuncer S, et al. Effect of surface roughness and biofilm formation on the color properties of resin-infiltrated ceramic and lithium disilicate glass-ceramic CAD-CAM materials. The Journal of Prosthetic Dentistry. 2024. doi:10.1016/j.prosdent.2024.02.005

BibTeX
@article{Topu2024,
  author = {Topçu, Sümeyra and Tekçe, Neslihan and Kopuz, Dilan and Özcelik, Eda Yazıcı and Kolaylı, Fetiye and Tuncer, Safa and Demirci, Mustafa},
  title = {Effect of surface roughness and biofilm formation on the color properties of resin-infiltrated ceramic and lithium disilicate glass-ceramic CAD-CAM materials},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2024},
  doi = {10.1016/j.prosdent.2024.02.005}
}
Kostenlos starten →