Comparative analysis of the physical, chemical, and microbiological properties of Ti-6Al-4V disks produced by different methods and subjected to surface treatments
The Journal of Prosthetic Dentistry · 2024
DOI: 10.1016/j.prosdent.2024.01.020 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2024. Verfasst von João Vicente Calazans Neto und 6 weiteren Autor:innen. Beteiligte Einrichtung: Master's student, Department of Dental Materials and Prosthodontics, Ribeirão Preto Dental School, University of São Paulo (USP), Ribeirão Preto, Bra…. Hauptthemen laut MEDLINE: Alloys, Titanium. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 76 Literaturangaben. Gefördert von: CNPq.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: To improve the osseointegration of dental implants and reduce microbiological growth, different micro- and nanoscale surface topographies can be used. PURPOSE: The purpose of this in vitro study was to evaluate the influence of Ti-6Al-4V with 4 surfaces, machined (DU), machined+hydroxyapatite (DUHAp), machined+acid-alkali treatment (DUAA), and additive manufacturing (DMA), on the physical, chemical, and microbiological properties. MATERIAL AND METHODS: The topography of Ti-6Al-4V disks with the 4 surfaces was evaluated by scanning electron microscopy (SEM), the chemical composition by energy dispersive X-ray spectroscopy (EDS), and the crystalline structure by X-ray diffraction (XRD). Physical and chemical properties were analyzed by using wettability and surface free energy, roughness, and microbial adhesion against Staphylococcus aureus by colony forming units (CFU). One-way ANOVA analysis of variance and the Tukey multiple comparisons test were applied to evaluate the data, except CFU, which was submitted to the Kruskal-Wallis nonparametric test (α=.05). RESULTS: DU photomicrographs showed a topography characteristic of a polished machined surface, DUHAp and DUAA exhibited patterns corresponding to the surface modifications performed, and in DMA the presence of partially fused spherical particles was observed. The EDS identified chemical elements inherent in the Ti-6Al-4V, and the DUHAp and DUAA disks also had the ions from the treatments applied. XRD patterns revealed similarities between DU and DMA, as well as characteristic peaks of hydroxyapatite (HA) in the DUHAp disk and the DUAA. Compared with DU and DMA the DUHAp and DUAA groups showed hydrophilic behavior with smaller contact angles and higher surface free energy (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Master's student, Department of Dental Materials and Prosthodontics, Ribeirão Preto Dental School, University of São Paulo (USP), Ribeirão Preto, Brazil.
- Professor, Department of Chemistry, Faculty of Philosophy, Sciences and Letters of Ribeirão Preto, University of São Paulo, (USP), Ribeirão Preto, Brazil.
- Professor, Professor, Federal University of São Carlos (UFSCar), São Carlos, Brazil.
- Researcher, Materials and Technologies, Department of Research, Development and Innovation, Institute of Welding and Quality (ISQ), Porto Salvo, Oeiras, Portugal.
- Professor, Department of Dental Materials and Prosthodontics, Ribeirão Preto Dental School, University of São Paulo (USP), Ribeirão Preto, Brazil.
- Professor, Department of Dental Materials and Prosthodontics, Ribeirão Preto Dental School, University of São Paulo (USP), Ribeirão Preto, Brazil. Electronic address: mariana.lima.valente@usp.br.
Förderung
- CNPq
Zitieren
APA
Calazans Neto, J. V., Ferreira, I., Ramos, A. P., Bolfarini, C., Batalha, R. L., Dos Reis, A. C., & Valente, M. L. D. C. (2024). Comparative analysis of the physical, chemical, and microbiological properties of Ti-6Al-4V disks produced by different methods and subjected to surface treatments. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2024.01.020
Vancouver
Calazans Neto JV, Ferreira I, Ramos AP, Bolfarini C, Batalha RL, Dos Reis AC, et al. Comparative analysis of the physical, chemical, and microbiological properties of Ti-6Al-4V disks produced by different methods and subjected to surface treatments. The Journal of Prosthetic Dentistry. 2024. doi:10.1016/j.prosdent.2024.01.020
BibTeX
@article{CalazansNeto2024,
author = {Calazans Neto, João Vicente and Ferreira, Izabela and Ramos, Ana Paula and Bolfarini, Claudemiro and Batalha, Rodolfo Lisboa and Dos Reis, Andréa Cândido and Valente, Mariana Lima da Costa},
title = {Comparative analysis of the physical, chemical, and microbiological properties of Ti-6Al-4V disks produced by different methods and subjected to surface treatments},
journal = {The Journal of Prosthetic Dentistry},
year = {2024},
doi = {10.1016/j.prosdent.2024.01.020}
}
EUVIMED