EUVIMEDEUVIMED entdecken
Vergleichsstudie

A comparative evaluation of photogrammetry software programs and conventional impression techniques for the fabrication of nasal maxillofacial prostheses

Muaiyed Mahmoud Buzayan, Aeman H Elkezza, Siti Fauzza Ahmad, Nosizana Mohd Salleh, Indumathi Sivakumar

The Journal of Prosthetic Dentistry · 2025

DOI: 10.1016/j.prosdent.2023.08.027 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift The Journal of Prosthetic Dentistry, 2025. Verfasst von Muaiyed Mahmoud Buzayan und 4 weiteren Autor:innen. Beteiligte Einrichtung: Senior Lecturer, Department of Restorative Dentistry, Faculty of Dentistry, University of Malaya, Kuala Lumpur, Malaysia. Electronic address: Muaiyed…. Hauptthemen laut MEDLINE: Photogrammetry, Software, Dental Impression Technique, Nose. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 19 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: The fabrication of facial prostheses is complicated and time-consuming because of the need for accurate impressions of the facial defects and surrounding tissues. Inaccuracies can arise from soft-tissue compression, involuntary patient movements, and insufficient support for the impression material. Various 3-dimensional (3D) imaging and scanning techniques, including photogrammetry, have been introduced, but their accuracy remains insufficiently evaluated. PURPOSE: The purpose of this in vitro study was to evaluate and compare the accuracy of 3D digital casts generated by 4 photogrammetry software programs (Agisoft Metashape, 3DF Zephyr, Meshroom, and Polycam) and casts from 2 conventional impression materials (alginate and polyvinyl siloxane [PVS]) for the fabrication of nasal maxillofacial prostheses. MATERIAL AND METHODS: A stone cast of a patient's nose was used as the basis for generating a reference digital 3D cast and another 54 test 3D casts. The reference cast was created by scanning the stone cast using a FARO Optor Lab 3D scanner. The 54 test 3D casts were generated and divided into 6 test groups as follows: Agisoft group: 9 3D casts generated using Agisoft Metashape, a commercial personal computer (PC) software program; 3DF Zephyr group: 9 3D casts generated using 3DF Zephyr, a commercial PC software program; Meshroom group: 9 3D casts generated using Meshroom, a free PC software program; Polycam group: 9 3D casts generated using the Polycam, a commercial Android cloud application; PVS group: 9 3D casts generated indirectly by 3D scanning a gypsum cast made from a polyvinyl siloxane (PVS) impression of the stone nose cast; and Alginate group: 9 3D casts generated indirectly by scanning a master cast made using alginate impressions of the stone nose cast. Deviation measurements of the produced specimens were analyzed using the Geomagic Control X software program, and statistical comparisons were performed employing the Kruskal-Wallis test (α=.05). RESULTS: The results showed that the 3DF Zephyr group had the smallest deviation measurements (median: 0.057 mm ±0.012) among the 4 photogrammetry software programs, while the alginate impression group had the largest deviations (median: 0.151 mm ±0.094) of the 2 conventional impression materials. Significant differences were observed among the 4 photogrammetry software programs and the 2 conventional impression materials (H=39.41, df=5, P .05). CONCLUSIONS: Photogrammetry software programs, specifically Agisoft Metashape and 3DF Zephyr, demonstrated better accuracy than conventional impression materials in creating nasal digital casts. Photogrammetry has the potential to improve workflow and reduce patient discomfort during the fabrication of maxillofacial prostheses. Further research is needed to validate these findings in clinical settings.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PhotogrammetrySoftwareDental Impression TechniqueNoseMaxillofacial ProsthesisProsthesis DesignHumansDental Impression MaterialsImaging, Three-DimensionalSiloxanesPolyvinylsComputer-Aided DesignAlginatesIn Vitro Techniques

Substanzen

Dental Impression MaterialsSiloxanesPolyvinylsAlginatesvinyl polysiloxane

Autor:innen und Institutionen

  • Senior Lecturer, Department of Restorative Dentistry, Faculty of Dentistry, University of Malaya, Kuala Lumpur, Malaysia. Electronic address: Muaiyed_zyan@hotmail.com.
  • Senior Lecturer, Department of Restorative Dentistry, Faculty of Dentistry, University of Malaya, Kuala Lumpur, Malaysia.
  • Associate Professor, Department of Restorative Dentistry, Faculty of Dentistry, University of Malaya, Kuala Lumpur, Malaysia.
  • Senior Lecturer, Department of Prosthodontic Dentistry, Faculty of Dentistry, SEGi University, Kota Damansara, Selangor, Malaysia.

Zitieren

APA

Buzayan, M. M., Elkezza, A. H., Ahmad, S. F., Mohd Salleh, N., & Sivakumar, I. (2025). A comparative evaluation of photogrammetry software programs and conventional impression techniques for the fabrication of nasal maxillofacial prostheses. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2023.08.027

Vancouver

Buzayan MM, Elkezza AH, Ahmad SF, Mohd Salleh N, Sivakumar I. A comparative evaluation of photogrammetry software programs and conventional impression techniques for the fabrication of nasal maxillofacial prostheses. The Journal of Prosthetic Dentistry. 2025. doi:10.1016/j.prosdent.2023.08.027

BibTeX
@article{Buzayan2025,
  author = {Buzayan, Muaiyed Mahmoud and Elkezza, Aeman H and Ahmad, Siti Fauzza and Mohd Salleh, Nosizana and Sivakumar, Indumathi},
  title = {A comparative evaluation of photogrammetry software programs and conventional impression techniques for the fabrication of nasal maxillofacial prostheses},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2025},
  doi = {10.1016/j.prosdent.2023.08.027}
}
Kostenlos starten →