EUVIMEDEUVIMED entdecken
Systematische ÜbersichtOpen Access · CC BY 4.0

Which clinical and laboratory procedures should be used to fabricate digital complete dentures? A systematic review

Khaing Myat Thu, Pedro Molinero-Mourelle, Andy Wai Kan Yeung, Samir Abou-Ayash, Walter Yu Hang Lam

The Journal of Prosthetic Dentistry · 2024-11 · 132 (5) · 922-938

DOI: 10.1016/j.prosdent.2023.07.027 ↗

Kurz gefasst

Systematische Übersicht in der Zeitschrift The Journal of Prosthetic Dentistry, 2024-11. Verfasst von Khaing Myat Thu und 4 weiteren Autor:innen. Beteiligte Einrichtung: Senior Research Assistant, Restorative Dental Sciences, Faculty of Dentistry, The University of Hong Kong, Hong Kong Special Adminstrative Region, PR…. Hauptthemen laut MEDLINE: Computer-Aided Design, Dental Impression Technique, Denture Design, Denture, Complete. Die Arbeit wurde bisher 37-mal zitiert (Crossref) und nennt 52 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Digital workflows for digital complete denture fabrication have a variety of clinical and laboratory procedures, but their outcomes and associated complications are currently unknown. PURPOSE: The purpose of this systematic review was to evaluate the clinical and laboratory procedures for digital complete dentures, their outcomes, and associated complications. MATERIAL AND METHODS: Electronic literature searches were conducted on PubMed/Medline, Embase, and Web of Science for studies published from January 2000 to September 2022 and screened by 2 independent reviewers. Information on digital complete denture procedures, materials, their outcomes, and associated complications was extracted. RESULTS: Of 266 screened studies, 39 studies were included. While 26 assessed definitive complete dentures, 7 studies assessed denture bases, 2 assessed trial dentures, and 4 assessed the digital images only. Twenty-four studies used border molded impression technique, 3 studies used a facebow record, and 7 studies used gothic arch tracing. Only 13 studies performed trial denture placement. Twenty-one studies used milling, and 17 studies used 3D printing for denture fabrication. One study reported that the retention of maxillary denture bases fabricated from a border-molded impression (14.5 to 16.1 N) was statistically higher than the retention of those fabricated from intraoral scanning (6.2 to 6.6 N). The maximum occlusal force of digital complete denture wearers was similar across different fabrication procedures. When compared with the conventional workflow, digital complete dentures required statistically shorter clinical time with 205 to 233 minutes saved. Up to 37.5% of participants reported loss of retention and up to 31.3% required a denture remake. In general, ≥1 extra visit and 1 to 4 unscheduled follow-up visits were needed. The outcomes for patient satisfaction and oral health-related quality of life were similar between conventional, milled, and 3D printed complete dentures. CONCLUSIONS: Making a border-molded impression is still preferred for better retention, and trial denture placement is still recommended to optimize the fabrication of definitive digital complete dentures.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Computer-Aided DesignDental Impression TechniqueDenture DesignDenture, CompleteHumansDenture BasesPrinting, Three-Dimensional

Autor:innen und Institutionen

  • Senior Research Assistant, Restorative Dental Sciences, Faculty of Dentistry, The University of Hong Kong, Hong Kong Special Adminstrative Region, PR China.
  • Research Assistant, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine University of Bern, Bern, Switzerland.
  • Tutor in Oral and Maxillofacial Radiology, Applied Oral Sciences and Community Dental Care, Faculty of Dentistry, The University of Hong Kong, Hong Kong Special Adminstrative Region, PR China.
  • Associate Professor, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland.
  • Clinical Assistant Professor in Prosthodontics, Restorative Dental Sciences, Faculty of Dentistry, The University of Hong Kong, Hong Kong Special Adminstrative Region, PR China.. Electronic address: retlaw@hku.hk.

Zitieren

APA

Thu, K. M., Molinero-Mourelle, P., Yeung, A. W. K., Abou-Ayash, S., & Lam, W. Y. H. (2024). Which clinical and laboratory procedures should be used to fabricate digital complete dentures? A systematic review. The Journal of Prosthetic Dentistry, 132(5), 922-938. https://doi.org/10.1016/j.prosdent.2023.07.027

Vancouver

Thu KM, Molinero-Mourelle P, Yeung AWK, Abou-Ayash S, Lam WYH. Which clinical and laboratory procedures should be used to fabricate digital complete dentures? A systematic review. The Journal of Prosthetic Dentistry. 2024;132(5):922-938. doi:10.1016/j.prosdent.2023.07.027

BibTeX
@article{Thu2024,
  author = {Thu, Khaing Myat and Molinero-Mourelle, Pedro and Yeung, Andy Wai Kan and Abou-Ayash, Samir and Lam, Walter Yu Hang},
  title = {Which clinical and laboratory procedures should be used to fabricate digital complete dentures? A systematic review},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2024},
  volume = {132},
  number = {5},
  pages = {922--938},
  doi = {10.1016/j.prosdent.2023.07.027}
}
Kostenlos starten →