EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY 4.0

Comparison of wear and fracture resistance of additively and subtractively manufactured screw-retained, implant-supported crowns

Almira Ada Diken Türksayar, Münir Demirel, Mustafa Borga Donmez, Emin Orkun Olcay, Tan Fırat Eyüboğlu, Mutlu Özcan

The Journal of Prosthetic Dentistry · 2024-07 · 132 (1) · 154-164

DOI: 10.1016/j.prosdent.2023.06.017 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift The Journal of Prosthetic Dentistry, 2024-07. Verfasst von Almira Ada Diken Türksayar und 5 weiteren Autor:innen. Beteiligte Einrichtung: Assistant Professor, Department of Prosthodontics, Faculty of Dentistry, Biruni University, Istanbul, Turkey; and Guest Researcher, ADMiRE Research C…. Hauptthemen laut MEDLINE: Crowns, Dental Prosthesis, Implant-Supported, Dental Restoration Failure, Dental Stress Analysis. Die Arbeit wurde bisher 47-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Additively manufactured resins indicated for fixed definitive prostheses have been recently marketed. However, knowledge on their wear and fracture resistance when fabricated as screw-retained, implant-supported crowns and subjected to artificial aging is limited. PURPOSE: The purpose of this in vitro study was to evaluate the volume loss, maximum wear depth, and fracture resistance of screw-retained implant-supported crowns after thermomechanical aging when fabricated using additively and subtractively manufactured materials. MATERIAL AND METHODS: Two additively manufactured composite resins (Crowntec [CT] and VarseoSmile Crown Plus [VS]) and 2 subtractively manufactured materials (1 reinforced composite resin, Brilliant Crios [BC] and 1 polymer-infiltrated ceramic network, Vita Enamic [EN]) were used to fabricate standardized screw-retained, implant-supported crowns. After fabrication, the crowns were cemented on titanium base abutments and then tightened to implants embedded in acrylic resin. A laser scanner with a triangular displacement sensor (LAS-20) was used to digitize the pre-aging state of the crowns. Then, all crowns were subjected to thermomechanical aging (1.2 million cycles under 50 N) and rescanned. A metrology-grade analysis software program (Geomagic Control X 2020.1) was used to superimpose post-aging scans over pre-aging scans to calculate the volume loss (mm3) and maximum wear depth (mm). Finally, all crowns were subjected to a fracture resistance test. Fracture resistance and volume loss were evaluated by using 1-way analysis of variance and Tukey Honestly significant difference (HSD) tests, whereas the Kruskal-Wallis and Dunn tests were used to analyze maximum wear depth. Chi-squared tests were used to evaluate the Weibull modulus and characteristic strength data (α=.05). RESULTS: Material type affected the tested parameters (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CrownsDental Prosthesis, Implant-SupportedDental Restoration FailureDental Stress AnalysisComposite ResinsMaterials TestingHumansDental Restoration WearIn Vitro TechniquesDental Prosthesis DesignDental MaterialsCeramicsBone Screws

Substanzen

Composite ResinsVITA EnamicDental Materials

Autor:innen und Institutionen

  • Assistant Professor, Department of Prosthodontics, Faculty of Dentistry, Biruni University, Istanbul, Turkey; and Guest Researcher, ADMiRE Research Center-Additive Manufacturing, Intelligent Robotics, Sensors and Engine…
  • Assistant Professor, Oral and Dental Health, Vocational School, Biruni University, Istanbul, Turkey.
  • Associate Professor, Department of Prosthodontics, Faculty of Dentistry, Istinye University, Istanbul, Turkey; and Visiting Researcher, Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine…
  • Assistant Professor, Department of Prosthodontics, Faculty of Dentistry, Istinye University, Istanbul, Turkey.
  • Associate Professor, Department of Endodontics, Istanbul Medipol University, Faculty of Dentistry, Istanbul, Turkey.
  • Professor and Head, Clinic of Masticatory Disorders and Dental Biomaterials, Center for Dental Medicine, University of Zurich, Zurich, Switzerland.

Zitieren

APA

Diken Türksayar, A. A., Demirel, M., Donmez, M. B., Olcay, E. O., Eyüboğlu, T. F., & Özcan, M. (2024). Comparison of wear and fracture resistance of additively and subtractively manufactured screw-retained, implant-supported crowns. The Journal of Prosthetic Dentistry, 132(1), 154-164. https://doi.org/10.1016/j.prosdent.2023.06.017

Vancouver

Diken Türksayar AA, Demirel M, Donmez MB, Olcay EO, Eyüboğlu TF, Özcan M. Comparison of wear and fracture resistance of additively and subtractively manufactured screw-retained, implant-supported crowns. The Journal of Prosthetic Dentistry. 2024;132(1):154-164. doi:10.1016/j.prosdent.2023.06.017

BibTeX
@article{DikenTrksayar2024,
  author = {Diken Türksayar, Almira Ada and Demirel, Münir and Donmez, Mustafa Borga and Olcay, Emin Orkun and Eyüboğlu, Tan Fırat and Özcan, Mutlu},
  title = {Comparison of wear and fracture resistance of additively and subtractively manufactured screw-retained, implant-supported crowns},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2024},
  volume = {132},
  number = {1},
  pages = {154--164},
  doi = {10.1016/j.prosdent.2023.06.017}
}
Kostenlos starten →