EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Fibroblast behavior on conventionally processed, milled, and printed occlusal device materials with different surface treatments

Vivien Bieger, Florian M Thieringer, Jens Fischer, Nadja Rohr

The Journal of Prosthetic Dentistry · 2023-06 · 129 (6) · 939-945

DOI: 10.1016/j.prosdent.2021.08.015 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2023-06. Verfasst von Vivien Bieger und 3 weiteren Autor:innen. Beteiligte Einrichtung: Postgraduate student, Biomaterials and Technology, Department of Reconstructive Dentistry, University Center for Dental Medicine Basel, Basel, Switze…. Hauptthemen laut MEDLINE: Dental Materials, Printing, Three-Dimensional. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

STATEMENT OF PROBLEM: Occlusal devices can be either conventionally processed, milled, or printed. However, little is known about the biocompatibility of 3D printing resin materials. PURPOSE: The purpose of this in vitro study was to compare the viability and morphology of human gingival fibroblast cells (HFG-1) after cultivation on conventionally processed, milled, and printed occlusal device materials with different surface treatments. MATERIAL AND METHODS: Disks of a conventionally processed (PalaXpress Clear [pP]), milled (Yamahachi PMMA Clear [sY]), and 2 different printed materials (Dental LT Clear Resin [aD]; Freeprint splint [aF]) were prepared. The surfaces of the specimens were finished by using 2 different treatments (unpolished and polished with P1200-grit silicon carbide paper). HGF-1 cells were cultivated on the specimens for 24 hours, and a viability assay was performed by using polystyrene disks as a control (n=9 disks per group). Cell morphology and the topography of the specimens were examined with scanning electron microscopy (n=3 disks per group). Two-way analysis of variance was applied to determine the effect of material and surface treatment followed by the post hoc Fisher least significant difference test (α=.05). RESULTS: Overall, material (P

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Dental MaterialsPrinting, Three-DimensionalHumansMaterials TestingFibroblastsSurface Properties

Substanzen

Dental Materials

Autor:innen und Institutionen

  • Postgraduate student, Biomaterials and Technology, Department of Reconstructive Dentistry, University Center for Dental Medicine Basel, Basel, Switzerland.
  • Assistant Professor, Senior consultant Oral and Cranio-Maxillofacial Surgery / Co-director 3D Print Lab, University Hospital Basel, Basel, Switzerland; and Head of Medical Additive Manufacturing Research Group (Swiss MA…
  • Professor emeritus, Biomaterials and Technology, Department of Reconstructive Dentistry, University Center for Dental Medicine Basel, Basel, Switzerland.
  • Assistant Professor, Head of Biomaterials and Technology, Department of Reconstructive Dentistry, University Center for Dental Medicine Basel, Basel, Switzerland. Electronic address: nadja.rohr@unibas.ch.

Zitieren

APA

Bieger, V., Thieringer, F. M., Fischer, J., & Rohr, N. (2023). Fibroblast behavior on conventionally processed, milled, and printed occlusal device materials with different surface treatments. The Journal of Prosthetic Dentistry, 129(6), 939-945. https://doi.org/10.1016/j.prosdent.2021.08.015

Vancouver

Bieger V, Thieringer FM, Fischer J, Rohr N. Fibroblast behavior on conventionally processed, milled, and printed occlusal device materials with different surface treatments. The Journal of Prosthetic Dentistry. 2023;129(6):939-945. doi:10.1016/j.prosdent.2021.08.015

BibTeX
@article{Bieger2023,
  author = {Bieger, Vivien and Thieringer, Florian M and Fischer, Jens and Rohr, Nadja},
  title = {Fibroblast behavior on conventionally processed, milled, and printed occlusal device materials with different surface treatments},
  journal = {The Journal of Prosthetic Dentistry},
  year = {2023},
  volume = {129},
  number = {6},
  pages = {939--945},
  doi = {10.1016/j.prosdent.2021.08.015}
}
Kostenlos starten →