EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

mSLAb – An open-source masked stereolithography (mSLA) bioprinter

Benedikt K Kaufmann, Matthias Rudolph, Markus Pechtl, Geronimo Wildenburg, Oliver Hayden, Hauke Clausen-Schaumann, Stefanie Sudhop

HardwareX · 2024-09 · 19 · e00543

DOI: 10.1016/j.ohx.2024.e00543 ↗

Kurz gefasst

Fachartikel in der Zeitschrift HardwareX, 2024-09. Verfasst von Benedikt K Kaufmann und 6 weiteren Autor:innen. Beteiligte Einrichtung: Center for Applied Tissue Engineering and Regenerative Medicine, Munich University of Applied Sciences, 80335 Munich, Germany. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: German Research Foundation, Bavarian State Ministry for Science and Art, Bavarian Academic Forum.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

3D bioprinting is a tissue engineering approach using additive manufacturing to fabricate tissue equivalents for regenerative medicine or medical drug testing. For this purpose, biomaterials that provide the essential microenvironment to support the viability of cells integrated directly or seeded after printing are processed into three-dimensional (3D) structures. Compared to extrusion-based 3D printing, which is most commonly used in bioprinting, stereolithography (SLA) offers a higher printing resolution and faster processing speeds with a wide range of cell-friendly materials such as gelatin- or collagen-based hydrogels and SLA is, therefore, well suited to generate 3D tissue constructs. While there have been numerous publications of conversions and upgrades for extrusion-based printers, this is not the case for state-of-the-art SLA technology in bioprinting. The high cost of proprietary printers severely limits teaching and research in SLA bioprinting. With mSLAb, we present a low-cost and open-source high-resolution 3D bioprinter based on masked SLA (mSLA). mSLAb is based on an entry-level (€350) desktop mSLA printer (Phrozen Sonic Mini 4 K), equipped with temperature control and humidification of the printing chamber to enable the processing of cell-friendly hydrogels. Additionally, the build platform was redesigned for easy sample handling and microscopic analysis of the printed constructs. All modifications were done with off-the-shelf hardware and in-house designed 3D printed components, printed with the same printer that was being modified. We validated the system by printing macroscopic porous scaffolds as well as hollow channels from gelatin-based hydrogels as representative structures needed in tissue engineering.

Schlagwörter

Stichwörter der Autor:innen

BioprinterBioprintingHydrogelStereolithographyTissue EngineeringmSLA

Autor:innen und Institutionen

  • Center for Applied Tissue Engineering and Regenerative Medicine, Munich University of Applied Sciences, 80335 Munich, Germany.
  • Center for NanoScience - CeNS, Ludwig Maximilian University of Munich, 80539 Munich, Germany.
  • Heinz-Nixdorf-Chair of Biomedical Electronics, School of Computation, Information and Technology & Munich Institute of Biomedical Engineering, Technical University of Munich, TranslaTUM, Einsteinstraße 25, 81675 Munich,…

Förderung

  • German Research Foundation
  • Bavarian State Ministry for Science and Art
  • Bavarian Academic Forum

Zitieren

APA

Kaufmann, B. K., Rudolph, M., Pechtl, M., Wildenburg, G., Hayden, O., Clausen-Schaumann, H., & Sudhop, S. (2024). mSLAb – An open-source masked stereolithography (mSLA) bioprinter. HardwareX, 19, e00543. https://doi.org/10.1016/j.ohx.2024.e00543

Vancouver

Kaufmann BK, Rudolph M, Pechtl M, Wildenburg G, Hayden O, Clausen-Schaumann H, et al. mSLAb – An open-source masked stereolithography (mSLA) bioprinter. HardwareX. 2024;19:e00543. doi:10.1016/j.ohx.2024.e00543

BibTeX
@article{Kaufmann2024,
  author = {Kaufmann, Benedikt K and Rudolph, Matthias and Pechtl, Markus and Wildenburg, Geronimo and Hayden, Oliver and Clausen-Schaumann, Hauke and Sudhop, Stefanie},
  title = {mSLAb – An open-source masked stereolithography (mSLA) bioprinter},
  journal = {HardwareX},
  year = {2024},
  volume = {19},
  pages = {e00543},
  doi = {10.1016/j.ohx.2024.e00543}
}
Kostenlos starten →