EUVIMEDEUVIMED entdecken
Crossref

Pressure-driven selective sublimation and electron-beam-induced sputtering during high vacuum heating observed by electron microscopy

Kyu-Jin Jo, Jin-Su Oh, Cheol-Woong Yang

Micron · 2026-07 · 205 · 104037

DOI: 10.1016/j.micron.2026.104037 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micron, 2026-07. Verfasst von Kyu-Jin Jo und 2 weiteren Autor:innen. Beteiligte Einrichtung: School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon 16419, Republic of Korea. Die Arbeit nennt 23 Literaturangaben. Gefördert von: Korea Basic Science Institute, Sungkyunkwan University, Korea Ministry of Science and ICT.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In situ heating transmission electron microscopy (TEM) enables real-time observation of microstructural evolution. However, interpretation can be hindered by artifacts arising from electron beam irradiation and the high-vacuum environment. In this study, (i) the vacuum effect was identified through an investigation of bulk surface behavior after ex situ heat treatment under atmospheric air, atmospheric argon, and high-vacuum (∼10-5 Pa) conditions, and (ii) the behavior of GeTe thin foils under different electron-beam conditions was examined using in situ heating TEM. Through these approaches, the electron-beam effects and vacuum effects were systematically investigated. As a result of bulk heat treatment performed at 450 ℃, oxidation occurred under an air atmosphere, Ge-Te interdiffusion and GeTe formation were observed under an Ar atmosphere, and under high-vacuum conditions, Te sublimation occurred, leading to the formation of a Ge-rich columnar structure. In situ CTEM revealed rapid electron-beam-induced sputtering of GeTe at 300 ℃, which led to hole formation in the electron-beam-irradiated regions under both 200 kV and 80 kV conditions. In contrast, sputtering was suppressed in in situ STEM using a low probe current. However, upon heating to 325 ℃, selective sublimation of Te and the consequent agglomeration of Ge occurred, leading to changes in stoichiometry and the formation of Ge nanocrystals. These results indicate that, for reliable in situ heating TEM analysis of GeTe, the beam current density should be minimized, and the selected temperature must be lower than the lowest sublimation onset temperature among the constituent elements under the vacuum conditions of the instrument.

Schlagwörter

Stichwörter der Autor:innen

In situ heating (S)TEMPressureSputteringSublimationex situ heating TEM

Autor:innen und Institutionen

  • School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon 16419, Republic of Korea.
  • School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon 16419, Republic of Korea. Electronic address: cwyang@skku.edu.

Förderung

  • Korea Basic Science Institute
  • Sungkyunkwan University
  • Korea Ministry of Science and ICT
  • Ministry of Education
  • National Research Foundation of Korea

Zitieren

APA

Jo, K. J., Oh, J. S., & Yang, C. W. (2026). Pressure-driven selective sublimation and electron-beam-induced sputtering during high vacuum heating observed by electron microscopy. Micron, 205, 104037. https://doi.org/10.1016/j.micron.2026.104037

Vancouver

Jo KJ, Oh JS, Yang CW. Pressure-driven selective sublimation and electron-beam-induced sputtering during high vacuum heating observed by electron microscopy. Micron. 2026;205:104037. doi:10.1016/j.micron.2026.104037

BibTeX
@article{Jo2026,
  author = {Jo, Kyu-Jin and Oh, Jin-Su and Yang, Cheol-Woong},
  title = {Pressure-driven selective sublimation and electron-beam-induced sputtering during high vacuum heating observed by electron microscopy},
  journal = {Micron},
  year = {2026},
  volume = {205},
  pages = {104037},
  doi = {10.1016/j.micron.2026.104037}
}
Kostenlos starten →