EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Method for fabricating self-powered cement sensors based on gold nanoparticles

Daniel A Triana-Camacho, Rogelio Ospina-Ospina, Jorge H Quintero-Orozco

MethodsX · 2023-12 · 11 · 102280

DOI: 10.1016/j.mex.2023.102280 ↗

Kurz gefasst

Fachartikel in der Zeitschrift MethodsX, 2023-12. Verfasst von Daniel A Triana-Camacho und 2 weiteren Autor:innen. Beteiligte Einrichtung: Escuela de Física, Universidad Industrial de Santander, Cra 27 Calle 9, Bucaramanga, Colombia. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 14 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Minciencias, Vicerrectoría de Investigación y Extensión, Universidad Industrial de Santander.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Nowadays, cement industry researchers are working hard to develop cement sensors based on nanocomposites because they can be used to develop intelligent and sustainable civil structures, self-powered, self-healing, or self-monitoring. In this light, this paper shows a methodology to obtain piezoelectric cement sensors, which produce enough energy not to require an external power source in sensing-strain applications. Mainly, two proposed experimental procedures increased the piezoelectric properties of these cement-based composites: add gold nanoparticles in the proper concentrations and apply a constant electric field during the curing stage. Firstly, the gold nanoparticles were obtained through a pulsed laser ablation system, and their particle size distribution was measured with a particle analyzer Litesizer 500 from Anton Paar, and their morphology was corroborated using a scanning electron microscope. Two concentrations (442 ppm and 658 ppm) of gold nanoparticles were obtained by changing the total ablation time. Next, we fabricated the cement sensors as described by ASTM standards C39-C39M. Hence, the cement was hand mixed with a water-to-cement ratio (w/c) of 0.47 for then poured on cylindrical molds saving the proportions recommended by the ASTM standard; in this stage, the gold nanoparticles were already part of the water ratio. Then, the cement sensors were cured under an external electric field and dried for 24 hours more in an oven to be finally ready for electromechanical characterization. Meanwhile, the electric response in altern current and the piezoelectric behavior were corroborated through electrical impedance spectroscopy and open circuit potential measurements, respectively. The piezoelectric behavior was obtained when a compressive strength was applied to the sensor, and the generated voltage was simultaneously measured. Finally, the electrical and mechanical characterization measurements were processed and analyzed using Python scripts.•The particle size and the families amount of Au NPs are affected by the ablation time.•The correct proportion of Au NPs increases the inherent piezoelectricity of cement paste.•The piezoelectric response can be addressed by coupling electric and mechanical tests.

Schlagwörter

Stichwörter der Autor:innen

Cement-based compositesGold nanoparticlesPiezoelectric properties for cement-based gold nanoparticlesPiezoelectricityPulsed laser ablation in liquid

Autor:innen und Institutionen

  • Escuela de Física, Universidad Industrial de Santander, Cra 27 Calle 9, Bucaramanga, Colombia.

Förderung

  • Minciencias
  • Vicerrectoría de Investigación y Extensión, Universidad Industrial de Santander

Zitieren

APA

Triana-Camacho, D. A., Ospina-Ospina, R., & Quintero-Orozco, J. H. (2023). Method for fabricating self-powered cement sensors based on gold nanoparticles. MethodsX, 11, 102280. https://doi.org/10.1016/j.mex.2023.102280

Vancouver

Triana-Camacho DA, Ospina-Ospina R, Quintero-Orozco JH. Method for fabricating self-powered cement sensors based on gold nanoparticles. MethodsX. 2023;11:102280. doi:10.1016/j.mex.2023.102280

BibTeX
@article{TrianaCamacho2023,
  author = {Triana-Camacho, Daniel A and Ospina-Ospina, Rogelio and Quintero-Orozco, Jorge H},
  title = {Method for fabricating self-powered cement sensors based on gold nanoparticles},
  journal = {MethodsX},
  year = {2023},
  volume = {11},
  pages = {102280},
  doi = {10.1016/j.mex.2023.102280}
}
Kostenlos starten →