EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Influence of the as quenched state and tempering temperature on the final microstructure and hardness of a high strength medium carbon steel

Ehsan Tolouei, Valentin Hurel, Abdelhalim Loucif, Jean-Benoit Morin, Mohammad Jahazi

Materials Chemistry and Physics · 2024-10 · 325 · 129765

DOI: 10.1016/j.matchemphys.2024.129765 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials Chemistry and Physics, 2024-10. Verfasst von Ehsan Tolouei und 4 weiteren Autor:innen. Die Arbeit wurde bisher 27-mal zitiert (Crossref) und nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The present study aimed to investigate the impact of the as-quenched microstructure and tempering temperature on the final microstructure and hardness of a medium-carbon, low-alloy steel using dilatometry, Electron backscatter diffraction (EBSD) and scanning electron microscopy (SEM). The results revealed substantial differences in the continuous heating stage of tempering in bainitic and martensitic samples, primarily attributed to the auto-tempering process during cooling. Tempering was carried out at 550 and 620 °C, and dilatometry results, along with microstructure analysis, indicated incomplete decomposition of retained austenite (RA) at both temperatures during a 30-min hold in the bainitic sample. The results show that non-decomposed RA, following the tempering of bainite, transformed into blocky fresh martensite, while no evidence of fresh martensite was observed in the martensitic sample. A new approach using EBSD and SEM images revealed that the decomposition of M/A (martensite/austenite constituent) zones in the bainitic sample resulted in the formation of a chain of aggregated chromium carbide zones at the grain boundaries. In contrast, the martensitic zone exhibited a uniform distribution of carbides in the microstructure. The stability of the phases was examined using the TCFE10 (thermodynamics) and MOBFE5 (mobility) modules of the DICTRA Themo-Calc software. Hardness measurements on all samples indicated decreases by about 18–24 % in the martensitic sample after tempering, while the bainitic sample exhibited a 5 % increase in hardness after tempering, attributed to secondary hardening and fresh martensite formation.

Zitieren

APA

Tolouei, E., Hurel, V., Loucif, A., Morin, J., & Jahazi, M. (2024). Influence of the as quenched state and tempering temperature on the final microstructure and hardness of a high strength medium carbon steel. Materials Chemistry and Physics, 325, 129765. https://doi.org/10.1016/j.matchemphys.2024.129765

Vancouver

Tolouei E, Hurel V, Loucif A, Morin J, Jahazi M. Influence of the as quenched state and tempering temperature on the final microstructure and hardness of a high strength medium carbon steel. Materials Chemistry and Physics. 2024;325:129765. doi:10.1016/j.matchemphys.2024.129765

BibTeX
@article{Tolouei2024,
  author = {Tolouei, Ehsan and Hurel, Valentin and Loucif, Abdelhalim and Morin, Jean-Benoit and Jahazi, Mohammad},
  title = {Influence of the as quenched state and tempering temperature on the final microstructure and hardness of a high strength medium carbon steel},
  journal = {Materials Chemistry and Physics},
  year = {2024},
  volume = {325},
  pages = {129765},
  doi = {10.1016/j.matchemphys.2024.129765}
}
Kostenlos starten →