EUVIMEDEUVIMED entdecken
Randomisierte kontrollierte Studie

Hand Sewn Anastomosis Skill Acquisition and In Vivo Transfer Using 3D-Printed Small Bowel Simulator

Merieme Habti, Florence Bénard, Léamarie Meloche-Dumas, Simon Bérubé, Dominic Cadoret, Artur Arutiunian, Yasmina Papas, Andrei Torres, Bill Kapralos, Frédéric Mercier, Adam Dubrowski, Erica Patocskai

Journal of Surgical Research · 2023-08 · 288 · 225-232

DOI: 10.1016/j.jss.2023.03.004 ↗

Kurz gefasst

Randomisierte kontrollierte Studie in der Zeitschrift Journal of Surgical Research, 2023-08. Verfasst von Merieme Habti und 11 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Medicine, Université de Montréal, Montreal, Quebec, Canada. Electronic address: merieme.habti@umontreal.ca. Hauptthemen laut MEDLINE: Anastomosis, Surgical, Internship and Residency, Intestine, Small. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 31 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

INTRODUCTION: General surgery residents need to master the hand-sewn bowel anastomosis (HSBA) technique. However, practice opportunities outside of the operating room are rare, and commercial simulators are often costly. The objective of this study is to assess the efficacy of a new, affordable silicone small bowel simulator, made with a three-dimensional (3D) printed mold, as a training tool to learn this technique. METHODS: This was a single-blinded pilot randomized controlled trial comparing two groups of eight junior surgical residents. All participants completed a pretest using an inexpensive, custom developed 3D-printed simulator. Next, participants randomized to the experimental group practiced the HSBA skill at home (eight sessions), while those randomized to the control group did not receive any hands-on practice opportunities. A posttest was done using the same simulator as for the pretest and practice sessions, and the retention-transfer test was performed on an anesthetized porcine model. Pretests, posttests and retention-transfer tests were filmed and graded by a blinded evaluator using assessments of technical skills, quality of final product, and tests of procedural knowledge. RESULTS: The experimental group significantly improved after practicing with the model (P = 0.01), while an equivalent improvement was not noted in the control group (P = 0.07). Moreover, the experimental group's performance remained stable between the posttest and the retention-transfer test (P = 0.95). CONCLUSIONS: Our 3D-printed simulator is an affordable and efficacious tool to teach residents the HSBA technique. It allows development of surgical skills that are transferable to an in vivo model.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Anastomosis, SurgicalInternship and ResidencyIntestine, SmallAnimalsAbdomenClinical CompetenceIntestinesPrinting, Three-DimensionalSwineHumans

Stichwörter der Autor:innen

3D-printingAnastomosisBowelSimulationSurgeryTraining

Autor:innen und Institutionen

  • Faculty of Medicine, Université de Montréal, Montreal, Quebec, Canada. Electronic address: merieme.habti@umontreal.ca.
  • Faculty of Medicine, Université de Montréal, Montreal, Quebec, Canada; Department of Surgery, Surgical Oncology Service, Centre Hospitalier de l'Université de Montréal (CHUM), Montreal, Quebec, Canada.
  • Faculty of Medicine, Université de Montréal, Montreal, Quebec, Canada.
  • Department of Health Sciences, Ontario Tech University, Oshawa, Ontario, Canada.
  • Department of Surgery, Surgical Oncology Service, Centre Hospitalier de l'Université de Montréal (CHUM), Montreal, Quebec, Canada.
  • Software Informatics Research Centre, Ontario Tech University, Oshawa, Ontario, Canada.

Zitieren

APA

Habti, M., Bénard, F., Meloche-Dumas, L., Bérubé, S., Cadoret, D., Arutiunian, A., Papas, Y., Torres, A., Kapralos, B., Mercier, F., Dubrowski, A., & Patocskai, E. (2023). Hand Sewn Anastomosis Skill Acquisition and In Vivo Transfer Using 3D-Printed Small Bowel Simulator. Journal of Surgical Research, 288, 225-232. https://doi.org/10.1016/j.jss.2023.03.004

Vancouver

Habti M, Bénard F, Meloche-Dumas L, Bérubé S, Cadoret D, Arutiunian A, et al. Hand Sewn Anastomosis Skill Acquisition and In Vivo Transfer Using 3D-Printed Small Bowel Simulator. Journal of Surgical Research. 2023;288:225-232. doi:10.1016/j.jss.2023.03.004

BibTeX
@article{Habti2023,
  author = {Habti, Merieme and Bénard, Florence and Meloche-Dumas, Léamarie and Bérubé, Simon and Cadoret, Dominic and Arutiunian, Artur and Papas, Yasmina and Torres, Andrei and Kapralos, Bill and Mercier, Frédéric and Dubrowski, Adam and Patocskai, Erica},
  title = {Hand Sewn Anastomosis Skill Acquisition and In Vivo Transfer Using 3D-Printed Small Bowel Simulator},
  journal = {Journal of Surgical Research},
  year = {2023},
  volume = {288},
  pages = {225--232},
  doi = {10.1016/j.jss.2023.03.004}
}
Kostenlos starten →