EUVIMEDEUVIMED entdecken
Crossref

The development of a 3D-printed relative motion orthosis and field testing of 3D and thermoplastic tape relative motion orthoses

Fatih Süleyman Okumuş, İlkem Ceren Sığırtmaç, Özge Buket Arslan, Deran Oskay, Çiğdem Öksüz

Journal of Hand Therapy · 2026-04

DOI: 10.1016/j.jht.2026.02.005 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Hand Therapy, 2026-04. Verfasst von Fatih Süleyman Okumuş und 4 weiteren Autor:innen. Beteiligte Einrichtung: Hacettepe University, Faculty of Health Sciences, Occupational Therapy Department Sıhhiye, Ankara, Turkey. Electronic address: fatihsuleyman.okumus@y…. Die Arbeit nennt 29 Literaturangaben. Gefördert von: Hacettepe Üniversitesi.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

BACKGROUND Three-dimensional (3D) printing offers an alternative for orthotic fabrication, particularly where thermoplastics are costly or not readily available. This report explored a universal-design 3D-printed relative motion orthosis and compared short-term user satisfaction with custom thermoplastic tape (Orficast) relative motion flexion orthoses. PURPOSE To design and produce universal 3D-printed relative motion orthosis using iterative prototyping and compare it with custom thermoplastic tape relative motion flexion orthoses. STUDY DESIGN Comparative field test with iterative prototype development. METHODS The study had two phases. In phase 1, a universal-design 3D relative motion orthosis was developed using repeated design-print-fit-refine cycles with feedback from an expert focus group. In phase 2, patients with Burton stage I boutonnière deformity were randomly assigned to wear either a 3D-printed relative motion flexion orthosis or a custom thermoplastic tape relative motion flexion orthosis for 1 week. User satisfaction was evaluated using the Turkish version of the Orthotics Prosthetics Users Survey (OPUS) satisfaction module. RESULTS Four prototypes and two final designs were produced; the final design met the focus-group checklist criteria. Forty participants were randomized (20 per group); nonadherence by four 3D group participants resulted in exclusion, leaving 16 (3D printed orthoses) and 20 (thermoplastic orthoses) for analysis (n = 36). OPUS Satisfaction scores did not differ significantly between groups after 1 week (3D printed orthoses: 93.19 ± 6.28 vs thermoplastic orthoses: 89.35 ± 11.17; p = 0.24). The material cost was €2.75 (US$3.19) for the 3D-printed orthosis vs €7.50 (US$8.70) for the thermoplastic tape orthosis in our setting. CONCLUSIONS In this study 3D printing lowered material costs and reduced therapist time compared to custom thermoplastic tape relative motion flexion orthoses. Patients with stage 1 Burton boutonniere deformity wearing the 3D-printed or custom thermoplastic tape relative motion flexion orthoses reported comparable satisfaction after 1-week wear time.

Schlagwörter

Stichwörter der Autor:innen

3D printed orthosesBoutonniere deformityCustom thermoplastic orthosesIterative prototypingPatient satisfaction

Autor:innen und Institutionen

  • Hacettepe University, Faculty of Health Sciences, Occupational Therapy Department Sıhhiye, Ankara, Turkey. Electronic address: fatihsuleyman.okumus@yuksekihtisas.edu.tr.
  • Cankiri Karatekin University, Faculty of Health Sciences, Occupational Therapy Department Uluyazı, Cankiri, Turkey.
  • Hacettepe University, Faculty of Health Sciences, Occupational Therapy Department Sıhhiye, Ankara, Turkey.
  • Gazi University, Faculty of Health Sciences, Department of Physical Therapy, Ankara, Turkey.

Förderung

  • Hacettepe Üniversitesi

Zitieren

APA

Okumuş, F. S., Sığırtmaç, İ. C., Arslan, Ö. B., Oskay, D., & Öksüz, Ç. (2026). The development of a 3D-printed relative motion orthosis and field testing of 3D and thermoplastic tape relative motion orthoses. Journal of Hand Therapy. https://doi.org/10.1016/j.jht.2026.02.005

Vancouver

Okumuş FS, Sığırtmaç İC, Arslan ÖB, Oskay D, Öksüz Ç. The development of a 3D-printed relative motion orthosis and field testing of 3D and thermoplastic tape relative motion orthoses. Journal of Hand Therapy. 2026. doi:10.1016/j.jht.2026.02.005

BibTeX
@article{Okumu2026,
  author = {Okumuş, Fatih Süleyman and Sığırtmaç, İlkem Ceren and Arslan, Özge Buket and Oskay, Deran and Öksüz, Çiğdem},
  title = {The development of a 3D-printed relative motion orthosis and field testing of 3D and thermoplastic tape relative motion orthoses},
  journal = {Journal of Hand Therapy},
  year = {2026},
  doi = {10.1016/j.jht.2026.02.005}
}
Kostenlos starten →